Dremel 225 Instrucciones para adjuntar documentos - Página 2
Navegue en línea o descargue pdf Instrucciones para adjuntar documentos para Herramientas Dremel 225. Dremel 225 2 páginas. Flex-shaft
También para Dremel 225: Manual de inicio rápido (2 páginas), Manual (16 páginas)
Imprimir página
2
3
1
ORDER BY PART NUMBER, NOT CODE NUMBER
COMMANDEZ PAR NUMÉRO DE PIÈCE ET NON PAR NUMÉRO DE CODE
PIDA POR NÚMERO DE PIEZA, NO POR NÚMERO DE CÓDIGO
CODE NO.
PART NO.
1
2615297355
2
480
481
482
483
3
2610914373
4
90962
5
2610914543
6
2610915085
7
529417870
NO. DE CODE
NO. DE PIÈCE
1
2615297355
2
480
481
482
483
3
2610914373
4
90962
5
2610914543
6
2610915085
7
529417870
NO. DE CÓDIGO
NO. DE PIEZA
1
2615297355
2
480
481
482
483
3
2610914373
4
90962
5
2610914543
6
2610915085
7
529417870
6
5
4
DESCRIPTION
Collet Nut (Not included)
1/8" Collet available as Accessory (Not included)
3/32" Collet available as Accessory (Not included)
1/16" Collet available as Accessory (Not included)
1/32" Collet available as Accessory (Not included)
Handpiece Cap
Wrench Available as Accessory (Not included)
Flexible Shaft Core
Overthrow Nut Assembly
Driver Cap
DESCRIPTION
Écrou de mors (fourni séparément)
Mors de 3,2 mm (1/8 po), accessoire fourni séparément
Mors de 2,4 mm (3/32 po), accessoire fourni séparément
Mors de 1,6 mm (1/16 po), accessoire fourni séparément
Mors de 0,8 mm (1/32 po), accessoire fourni séparément
Tapa del Mango
Clé accessoire (fournie séparément)
me d'arbre flexible
Conjunto de tuerca
Capuchon moteur
DESCRIPCION
Tuerca del portaherramienta (no incluida)
Portaherramienta de 1/8" disponible como accesorio (no incluido)
Portaherramienta de 3/32" disponible como accesorio (no incluido)
Portaherramienta de 1/16" disponible como accesorio (no incluido)
Portaherramienta de 1/32" disponible como accesorio (no incluido)
Chapeau de la pièce manuelle
Llave de tuerca disponible como accesorio (no incluida)
Núcleo del eje flexible
Ensemble d'écrou de renversement
Tapa del impulsor
7
Flex-Shaft Attachment Instructions
Model 225
Safety Rules for Flex-Shaft
Read and understand the tool
WARNING
!
manual and these instructions
for the use of this accessory with your tool.
Failure to follow all instructions listed below may
result in serious personal injury.
Wear ANSI compliant eye protection. The
operation of any power tool can result in foreign
objects being thrown into the eyes.
Do not operate the flexible shaft with a sharp or
multiple bends. Over
bending the shaft can
generate excessive heat on
the jacket or hand piece
and may cause the flexible
5" RADIUS
shaft to disengage from
tool. The minimum
recommended bend radius is 5"
Always hold the hand piece firmly in your
hands during the start-up. The reaction torque of
the motor, as it accelerates to full speed, can cause
the shaft to twist.
Not for use with router bits or other large
diameter cutting bits. Large diameter cutting bits
can cause kickback and loss of control when used
with the flexible shaft.
Do not remove end ferrule while tool is running.
The cable will become loose from the jacket and
will uncontrollably whip or lash around.
Attachment for use with Dremel Rotary Tool
Models 275, 285, 395, 398 & 780.
Installation Instructions
It is extremely important to carefully read and follow the
directions to assemble the flex-shaft to your rotary tool
below to ensure the tool will function properly.
To properly attach the flex-shaft to the rotary tool,
THREE items must be removed from the tool: the
housing cap, collet nut and collet.
Step 1. Press the Shaft lock button, unscrew and
remove the collet nut.
Step 2. Unscrew the housing cap from the tool.
HOUSING
CAP
COLLET
(inside)
2610914687 02/02
Collet and Accessory Assembly
The collet assembly consists of a collet nut and
collet. Take the collet nut and collet that were
removed from your tool in step 2 and 3 and insert
them into the tip of the flex-shaft handpiece.
Step 3. Remove the collet.
Insert an accessory or bit as deeply as possible to
avoid wobble during use. With the shaft lock button
engaged on the flex-shaft handpiece retighten the
collet nut.
Note: If the collet nut and collet are not
removed from the motor shaft, the tool will
not function properly.
Step 4. Install the driver cap on the motor
shaft and tighten.
DRIVER
CAP
Collet Removal and Replacement
Four different size collets to accommodate different
shank sizes, are sold separately for your flex-shaft.
To install a different collet, remove the collet nut and
MOTOR
remove the old collet. Insert the unslotted end of the
SHAFT
collet in the hole in the end of the flex-shaft. Replace
To prevent damage to tool,
collet nut on the shaft. Always use the collet
CAUTION
!
do not overtighten driver
which matches the shank size of the accessory
cap. Tighten the driver cap finger tight and then
you plan to use. Never force a larger diameter
tighten an additional 1/3 turn with the wrench.
shank into a collet.
(Wrench included with your rotary tool kit)
Collet Identification Chart – Collet sizes can be
identified by the rings on the back end of collet.
Step 5. Attach by screwing the collar of the
flex-shaft to the rotary tool. Make sure the
square end of the center core engages the
square hole socket in the driver cap.
Model No.
480
481
Flexible Shaft Lubrication
Do not pull out center core
CAUTION
!
to engage into driver cap.
CAUTION
!
This could cause disengagement of center core
hours of use. To lubricate, unscrew the flex-shaft
from handpiece. If tool stops when shaft is bent,
assembly from the motor housing. Pull the center
center core may be lodged in driver cap. Loosen
core out of the flex-shaft assembly. Wipe a very
shaft and remove core from driver cap. Then
thin film automotive wheel bearing grease on to
screw flexible shaft onto rotary tool housing
the center core and reinsert it back into the shaft.
again.
To prevent damage to tool do not over grease
shaft. Too much grease will cause the unit to
Operating Instructions
overheat.
Disengagement of the Flex-Shaft
Reattach the flex-shaft to the rotary tool.
The flexible shaft may become disengaged if
the motor of your rotary tool is not elevated
Contents of 225 Flex-Shaft Attachment
higher than the working end of the flex-shaft.
Qty.
Description
The #2222 Rotary Tool Stand is recommended
1
Flex-Shaft Assembly (42" long)
to hold the rotary tool at the proper height.
1
Driver Cap
SHAFT LOCK
BUTTON
Identification rings
1/32" Collet has one (1) ring.
1/16" Collet has two (2) rings.
3/32" Collet has three (3) rings.
1/8" Collet has no rings.
AVAILABLE COLLETS
Size
Model No.
Size
1/8"
482
1/16"
3/32"
483
1/32"
The flex-shaft should be
lubricated after every 25-30
PRINTED IN U.S.A.