Dremel 225 Petunjuk Pemasangan - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Pemasangan untuk Peralatan Dremel 225. Dremel 225 2 halaman. Flex-shaft
Juga untuk Dremel 225: Panduan Memulai Cepat (2 halaman), Manual (16 halaman)

Halaman Cetak

ORDER BY PART NUMBER, NOT CODE NUMBER

COMMANDEZ PAR NUMÉRO DE PIÈCE ET NON PAR NUMÉRO DE CODE

PIDA POR NÚMERO DE PIEZA, NO POR NÚMERO DE CÓDIGO

CODE NO.

PART NO.

2615297355

480

481

482

483

2610914373

90962

2610914543

2610915085

529417870

NO. DE CODE

NO. DE PIÈCE

2615297355

480

481

482

483

2610914373

90962

2610914543

2610915085

529417870

NO. DE CÓDIGO

NO. DE PIEZA

2615297355

480

481

482

483

2610914373

90962

2610914543

2610915085

529417870

DESCRIPTION

Collet Nut (Not included)

1/8" Collet available as Accessory (Not included)

3/32" Collet available as Accessory (Not included)

1/16" Collet available as Accessory (Not included)

1/32" Collet available as Accessory (Not included)

Handpiece Cap

Wrench Available as Accessory (Not included)

Flexible Shaft Core

Overthrow Nut Assembly

Driver Cap

DESCRIPTION

Écrou de mors (fourni séparément)

Mors de 3,2 mm (1/8 po), accessoire fourni séparément

Mors de 2,4 mm (3/32 po), accessoire fourni séparément

Mors de 1,6 mm (1/16 po), accessoire fourni séparément

Mors de 0,8 mm (1/32 po), accessoire fourni séparément

Tapa del Mango

Clé accessoire (fournie séparément)

me d'arbre flexible

Conjunto de tuerca

Capuchon moteur

DESCRIPCION

Tuerca del portaherramienta (no incluida)

Portaherramienta de 1/8" disponible como accesorio (no incluido)

Portaherramienta de 3/32" disponible como accesorio (no incluido)

Portaherramienta de 1/16" disponible como accesorio (no incluido)

Portaherramienta de 1/32" disponible como accesorio (no incluido)

Chapeau de la pièce manuelle

Llave de tuerca disponible como accesorio (no incluida)

Núcleo del eje flexible

Ensemble d'écrou de renversement

Tapa del impulsor

Flex-Shaft Attachment Instructions

Model 225

Safety Rules for Flex-Shaft

Read and understand the tool

WARNING

manual and these instructions

for the use of this accessory with your tool.

Failure to follow all instructions listed below may

result in serious personal injury.

Wear ANSI compliant eye protection. The

operation of any power tool can result in foreign

objects being thrown into the eyes.

Do not operate the flexible shaft with a sharp or

multiple bends. Over

bending the shaft can

generate excessive heat on

the jacket or hand piece

and may cause the flexible

5" RADIUS

shaft to disengage from

tool. The minimum

recommended bend radius is 5"

Always hold the hand piece firmly in your

hands during the start-up. The reaction torque of

the motor, as it accelerates to full speed, can cause

the shaft to twist.

Not for use with router bits or other large

diameter cutting bits. Large diameter cutting bits

can cause kickback and loss of control when used

with the flexible shaft.

Do not remove end ferrule while tool is running.

The cable will become loose from the jacket and

will uncontrollably whip or lash around.

Attachment for use with Dremel Rotary Tool

Models 275, 285, 395, 398 & 780.

Installation Instructions

It is extremely important to carefully read and follow the

directions to assemble the flex-shaft to your rotary tool

below to ensure the tool will function properly.

To properly attach the flex-shaft to the rotary tool,

THREE items must be removed from the tool: the

housing cap, collet nut and collet.

Step 1. Press the Shaft lock button, unscrew and

remove the collet nut.

Step 2. Unscrew the housing cap from the tool.

HOUSING

CAP

COLLET

(inside)

2610914687 02/02

Collet and Accessory Assembly

The collet assembly consists of a collet nut and

collet. Take the collet nut and collet that were

removed from your tool in step 2 and 3 and insert

them into the tip of the flex-shaft handpiece.

Step 3. Remove the collet.

Insert an accessory or bit as deeply as possible to

avoid wobble during use. With the shaft lock button

engaged on the flex-shaft handpiece retighten the

collet nut.

Note: If the collet nut and collet are not

removed from the motor shaft, the tool will

not function properly.

Step 4. Install the driver cap on the motor

shaft and tighten.

DRIVER

CAP

Collet Removal and Replacement

Four different size collets to accommodate different

shank sizes, are sold separately for your flex-shaft.

To install a different collet, remove the collet nut and

MOTOR

remove the old collet. Insert the unslotted end of the

SHAFT

collet in the hole in the end of the flex-shaft. Replace

To prevent damage to tool,

collet nut on the shaft. Always use the collet

CAUTION

do not overtighten driver

which matches the shank size of the accessory

cap. Tighten the driver cap finger tight and then

you plan to use. Never force a larger diameter

tighten an additional 1/3 turn with the wrench.

shank into a collet.

(Wrench included with your rotary tool kit)

Collet Identification Chart – Collet sizes can be

identified by the rings on the back end of collet.

Step 5. Attach by screwing the collar of the

flex-shaft to the rotary tool. Make sure the

square end of the center core engages the

square hole socket in the driver cap.

Model No.

480

481

Flexible Shaft Lubrication

Do not pull out center core

CAUTION

to engage into driver cap.

CAUTION

This could cause disengagement of center core

hours of use. To lubricate, unscrew the flex-shaft

from handpiece. If tool stops when shaft is bent,

assembly from the motor housing. Pull the center

center core may be lodged in driver cap. Loosen

core out of the flex-shaft assembly. Wipe a very

shaft and remove core from driver cap. Then

thin film automotive wheel bearing grease on to

screw flexible shaft onto rotary tool housing

the center core and reinsert it back into the shaft.

again.

To prevent damage to tool do not over grease

shaft. Too much grease will cause the unit to

Operating Instructions

overheat.

Disengagement of the Flex-Shaft

Reattach the flex-shaft to the rotary tool.

The flexible shaft may become disengaged if

the motor of your rotary tool is not elevated

Contents of 225 Flex-Shaft Attachment

higher than the working end of the flex-shaft.

Qty.

Description

The #2222 Rotary Tool Stand is recommended

Flex-Shaft Assembly (42" long)

to hold the rotary tool at the proper height.

Driver Cap

SHAFT LOCK

BUTTON

Identification rings

1/32" Collet has one (1) ring.

1/16" Collet has two (2) rings.

3/32" Collet has three (3) rings.

1/8" Collet has no rings.

AVAILABLE COLLETS

Size

Model No.

Size

1/8"

482

1/16"

3/32"

483

1/32"

The flex-shaft should be

lubricated after every 25-30

PRINTED IN U.S.A.