Alert 750R-LCD Manual del usuario - Página 6
Navegue en línea o descargue pdf Manual del usuario para Alarma de coche Alert 750R-LCD. Alert 750R-LCD 15 páginas. Remote starter and security system
Imprimir páginaOVErrIdE THE ALArm WITH pASSWOrd pIN COdE:
If the valet switch easily found, and defeated, this security system allows the consumer to
program a password pin code. Offering a higher level of security.
. Enter the vehicle and turn the ignition switch to ' ON' position. (Alarm will sound.)
. Within 5 seconds, enter your chosen the first digit code by pressing and releasing the Valet Switch.
. (When finished above procedures, system's siren stop alarming, parking light stop flashing, but
the vehicle cannot be start and drive away.)
4. Within 5 seconds of the last digit code enter (the st code), turn the Ignition Switch " OFF" and
then " ON".
5. Within 5 seconds, enter your chosen of the second digit code by pressing and releasing the
Valet Switch.
6. Turn the ignition switch " OFF" position. [4] Chirps form siren/horn, [] flash from parking light
to indicate the system was disarmed.
Note: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAmpLE: To Override The System With The password Code 83, you would;
. Enter the vehicle and turn the ignition switch to ' ON' position. (Alarm will sound.)
. Within 5 seconds, Press and Release the Valet Switch 8 times
. (When finished above procedures, system's siren stops alarming, parking light stop flashing,
other sensor stop trigger, but the vehicle can not be start and drive away.)
4. Within 5 seconds of the last digit code enter (the st code), turn the Ignition Switch " Off" and
then " ON".
5. Within 5 seconds, Press and Release the Valet Switch times
6. Turn the Ignition Switch to " Off" position. [4] Chirps form siren/horn, [] flash from parking
light to indicate the system was disarmed.
K. VALet moDe: (System in Disarm or Valet mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm function is bypassed, however the remote panic feature and remote door locks will remain
operational. To use the valet mode, the system must first be disarmed either by using you remote
transmitter, or by operating the Manual override sequence.
0
Enter Valet mode:
. From the disarmed condition, turn the ignition to " ON" position.
. Push and hold valet switch for seconds until the LED turns on. The LED
wills remain on as long as the system is in ' valet mode' .
Exit Valet mode:
. Return to normal operation, turn ignition ' on' .
. Push and hold valet switch for seconds, The LED will turn off indicating
the system is exiting the valet mode.
rEmOTE VALET: (System in Disarm or Valet mode)
Press and release
button on the transmitter three times within seconds to enter / exit valet mode.
A parking flash to confirm enters valet mode and two parking lights flashing to confirm exit valet mode.
L. CAR LoCAtoR
Press the button to activate the car locator function. The siren will chirp 6
times. The parking light will flash times, for you to easily locate your car.
m. PANIC FUNCtIoN:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case emergency.
. Press and hold the button for second. The alarm will immediately
sound.
. During panic mode, the normal function of this transmitter button will be suspended. The
and buttons can be used to lock and unlock the doors (if the option is installed), however
once the button is pressed, the vehicle's starter disable device, (where installed) will be
disabled allowing the vehicle to start.
Remote Door Lock
Remote Door Un-Lock