Alert 750R-LCD Manual del usuario - Página 7
Navegue en línea o descargue pdf Manual del usuario para Alarma de coche Alert 750R-LCD. Alert 750R-LCD 15 páginas. Remote starter and security system
Imprimir página. To stop the alarm, press and hold the or button on the transmitter again for seconds.
Also if any transmitter button other than or button is pressed and released, the panic
mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 0 seconds.
N. tRIGGeR tHe SYStem
When armed, your vehicle is protected as follows:
. Light impact will trigger the warn-away signal.
. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle's starter from cranking. The siren, horn,
parking lights, and dome light will turn on to alerting of an intrusion for 0 seconds. Then it will
stop and automatic reset and re-arm. If the one of sensors or detectors still activate, the alarm
system will sound a maximum of 6 times of 0 seconds cycles.
Trunk/Hood
Trigger
door Trigger
STOp THE mELOdY SOUNd ONLY: While triggering the alarm the LCD screen will alert user
through melody sound and flashing trigger icon, press any button on the LCD remote transceiver
to stop melody sound only
CLEAr THE FLASH ICON ANd mELOdY SOUNd: While triggering the alarm the LCD screen will
alert user through melody sound and flashing trigger icon, press the F button times within
seconds will clear the flash icon and stop melody sound on the LCD screen transceiver.
NOISE ABATEmENT CIrCUIT: You system has " Noise Abatement Circuit". It prevents annoying
repetitive trigger sequences due to faulty door pin switches or environmental condition such as
thunder, jackhammers airport noise, etc.
Shock Sensor
Ignition Trigger
Warn-Away
Trigger
Here's how "Noise Abatement Circuit" works: The alarm triggers five times. Each time, the
same sensor or switch is triggering the alarm. " Noise Abatement Circuit" will interpret this pattern
of triggers as false alarm. After the fifth trigger, " Noise Abatement Circuit" ignores, or bypasses,
that sensor or switch until the other sensor or switch is trigger.
"Noise Abatement Circuit" covers doors (Hood/Trunk) differently: If the alarm is triggered by an
open door for six full cycles, the doors will be bypassed until the trigger ceases.
o. ANtI CAR- JACKING
Warning: If you don't need the anti car jacking function in this alarm system, be sure to set car
jacking feature " OFF". This system is default setting all car-jacking " OFF".
ACTIVE ANTI CAr JACKINg:
. Press and hold the transmitter and buttons at the same time for seconds while the
vehicle's ignition is ON. The parking lights will turns on for .5 seconds to indicate the system
enters the anti car-jacking mode.
. Once the system is in the anti car-jacking mode, If you are forced from the vehicle, the system
will be trigger when the door is opened and closed while the ignition is " ON".
Trigger
pASSIVE ANTI CAr- JACKINg:
. Turn the ignition switch to " ON" position; the system enters the anti car-jacking mode.
. Once the system is in the anti car-jacking mode, If you are forced from the vehicle, the system
will trigger when the door is opened and closed while the ignition is " ON".
TrIggEr THE ANTI CAr -JACKINg mOdE:
a). 50 seconds after the system has been triggered. The siren will start chirping for 5 seconds.
b). During this 5 seconds period of chirping, you will be alerted to push the valet switch once to
turn off the anti car-jacking feature. If not, it will enter second timer car jacking.
c). 65 seconds after the system has beer triggered. The siren starts alarming and the parking light
starts flashing.
d). 90 seconds after the system has been triggered
. The siren still alarming and the parking light flashing, and
. The starter disable will activate to prevent the vehicle from starting.
. It will remain active until the vehicle's battery power is exhausted.