Casio 2330 Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Ver Casio 2330. Casio 2330 2 páginas. Casio watch user guide

Module No. 2330

Press B to change from mode to mode.

If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.

Timekeeping Mode

TIMEKEEPING MODE

Pressing C in the Timekeeping Mode illuminates the display for about two sec-

onds. The backlight is disabled while a setting screen is on the display.

When using 12-hour timekeeping, a P appears on the display for "pm" times (noon

to 11:59 pm). An "am" time (midnight to 11:59 am) is indicated when there is no P

indicator on the display. 24-hour timekeeping is being used when the 24 indicator is

on the display.

Hour hand

Second hand

To set the time and date

1. While in the Timekeeping Mode, hold down A until the

24 indicator

2. Press B to move the flashing in the sequence shown below.

Press B.

Seconds

Day

Month

3. While the seconds setting is selected (flashing), press C to reset it to 00.

If you press C while the seconds setting is in the range of 30 to 59, the seconds

are reset to 00 and 1 is added to the minutes. If the seconds setting is in the range

of 00 to 29, the minutes count is unchanged.

While the DST (Daylight Saving Time) setting is selected, press C to toggle it on

and off.

DST indicator 2

DST indicator 1

DST OFF

Daylight Saving Time (DST), which is also sometimes called "summer time" ad-

vances the time for one hour, as is the custom in some areas during the summer.

Remember that not all countries or even local areas use Daylight Saving Time.

DST indicator 1 flashes while the DST setting is selected. It also appears in the

Timekeeping Mode and Alarm Mode to indicate that DST is turned on. DST indica-

tor 1 does not appear in the Timekeeping Mode when DST is turned off.

DST indicator 2 appears (flashing) only while the DST setting is selected on the

setting screen. 0 indicates that DST is turned off, while 1 indicates that DST is

turned on.

While the 12/24 setting is selected, press C to toggle it between 12-hour and 24-

hour timekeeping.

4. While any other digits are selected (flashing), press C to increase the selected

digits. Holding down changes them at high speed.

5. After you make the settings you want, press A to exit the setting screen.

The day of the week is automatically set in accordance with the date.

The date can be set within the range of January 1, 2000 to December 31, 2039.

When setting the year, you need to specify only the rightmost two digits. To specify

the year 2001, for example, set 01.

To set the hands

When the analog setting does not match the time shown on the display, use the

following procedure to correct the analog setting.

1. When the second hand reaches the 12 o'clock position (00 seconds), pull out the

crown to stop the second hand.

2. Hold down A until the seconds digits appear and flash on the display.

3. Rotate the crown to set the hour and minutes.

4. When the seconds count on the digital display reaches 00, press in the crown to

restart the second hand.

5. Press A to exit the setting screen.

Countdown Alarm Mode

Press B.

Minute hand

PM indicator

Hour : Minutes

Month

Day of week

Day

seconds digits appear and flash on the display. This

indicates the setting screen.

DST

Hour

Minutes

Year

DST indicator 2

DST indicator 1

Press C.

DST ON

GENERAL GUIDE

About the Auto Light Switch Function

When the auto light switch function is turned on, the backlight automatically turns on

for two seconds under the conditions described below. Avoid wearing the watch on

the inside of your wrist. Doing so causes the auto light switch to operate when not

needed, which shortens battery life.

Moving the watch to a position that is parallel to the ground and then tilting it

towards you approximately 40 degrees causes the backlight to illuminate.

The backlight may not illuminate if the face of the watch is more than 15 degrees off

parallel to the left or right. Make sure that the back of your hand is parallel to the

ground.

Parallel to ground

Static electricity or magnetic force can interfere with proper operation of the auto

light switch function. If the backlight does not illuminate, try moving the watch back

to the starting position (parallel with the ground) and then tilt it back toward you

again. If this does not work, drop your arm all the way down so it hangs at your side,

and then bring it back up again.

Under certain conditions the backlight may not light until about one second or less

after turn the face of the watch towards you. This does not necessarily indicate

malfunction of the backlight.

To switch the auto light switch function on and off

12/24

In the Timekeeping Mode (except when making any settings), hold down C for two

seconds to turn the auto light switch function on and off.

The auto light switch indicator is shown on the display in all modes while the auto

light switch function is on.

In order to protect against running down the battery, the auto light switch function is

automatically turned off approximately five hours after you turn it on. Repeat the

above procedure to turn the auto light switch function back on if you want.

Pressing C in the Timekeeping Mode (except when making any settings) illumi-

nates the display, regardless of the auto light switch's on/off setting.

Caution

The backlight of this watch employs an electro-luminescent (EL) light, which loses

its illuminating power after very long term use.

Frequent use of the backligfht shortens the battery life.

The watch emits an audible sound whenever the display is illuminated. This is be-

cause the EL light vibrates slightly when lit. It does not indicate malfunction of the

watch.

Warning!

Never try to read your watch when mountain climbing or hiking in areas that

are dark or in areas with poor footing. Doing so is dangerous and can result

in serious personal injury.

Never try to read your watch when running where there is the danger of acci-

dents, especially in locations where there might be vehicular or pedestrian

traffic. Doing so is dangerous and can result in serious personal injury.

Never try to read your watch when riding on a bicycle or when operating a

motorcycle or any other motor vehicle. Doing so is dangerous and can result

in a traffic accident and serious personal injury.

When you are wearing the watch, make sure that its auto light switch function

is turned off before riding on a bicycle or operating a motorcycle or any other

motor vehicle. Sudden and unintended operation of the auto light switch can

create a distraction, which can result in a traffic accident and serious personal

injury.

Day Counter Mode

ABOUT THE BACKLIGHT

Parallel to ground

More than 15 degrees

too high

Auto light switch

indicator

Hold down C.

2330-1

Alarm Mode

More than 15 degrees

too low

OFF