DataComm 50-3323 Manual de instrucciones e instalación
Navegue en línea o descargue pdf Manual de instrucciones e instalación para Accesorios DataComm 50-3323. DataComm 50-3323 2 páginas.
Imprimir páginaInstruction I Installation Sheet
DataComm Electronics 50-3323 Recessed Pro-Power Installation Kit
DATA
innDv.tive struc:t:ur-!!d wiring
DataComm Electronics, Inc.
6349 Peachtree Street
Noraoss, GA 30071-1725
888.223.7977
770.662.8205
www.datacornmeledronics.com
Parts Included:
1.
Recessed Cable Plate with Power
2.
Recessed Cable Plate with Straight Blade Inlet
3.
6 Ft. Extension Cord
4.
Two (2) Old Work Electrical Boxes
5.
8 Ft. of Non-Metallic Electrical Wire
6.
Three (3) Wire Nuts
Tools Needed
1.
Drywall saw
2.
6 Ft. tape measure
3.
Pencil
4.
Screwdriver
Use the Recessed Pro-Power Installation Kit to install power and
low voltage cables behind your flat panel TV (see
Figures
1 &
2), amplifier or other audio and video devices to your equipment
room or at the location of your head end equipment.
IMPORTANT INSTRUCTIONS:
Only use the National Electrical Code approved
installation when installing this product.
•
This product is not designed to be part of your home or a
commercial building's electrical wiring system.
This installation is only energized (electrically active)
when the supplied 6 ft. cord is plugged into the recessed
straight blade inlet located on the recessed low voltage
cable plate and the straight blade end of the 6 ft. cord is
plugged into either your surge protector or wall
receptade.
If you are not familiar with home wiring systems, please
call a qualified electrician to install this product.
Installation Instructions for New Construction:
Simply use a new nail on box and follow all other instructions
described in the retrofit portion of the instruction sheet.
Installation Instructions for Retrofit Only:
1.
Select the location of your flat panel TV mounting
bracket. Now select the location for both the Recessed
Cable Plate with Power and the Recessed Cable Plate
with Straight Blade Inlet.
2.
Both the Recessed Cable Plate with Power and the
Recessed Cable Plate with Straight Blade Inlet are
designed to be mounted between two studs (see
Figure
1). Using the template supplied (see
page 2),
trace the openings needed for both recessed cable
plates. Using a drywall knife cut a hole in the drywall the
size of the template. Remember, these plates are
designed to be mounted between two studs.
3.
Remember that the Pro-Power Installation Kit is not
part
of
your home's electrical wiring system. Before
installing the single gang retrofit workboxes (see
Figure
2), pull a piece of 12/2 or 14/2 with ground UL approved
building wire from one opening to the other opening to
connect the Recessed Cable Plate with Power to the
Recessed Cable Plate with Straight Blade Inlet. Make
sure the piece of wire is long enough to allow for easy
installation of the receptades. Insert a single gang
retrofit worXbox (see
Figure
2). Securely fasten the
workbox to the wall.
50-3323-WH-KIT
Figure 1- Front View
Concealed Wrring
Ihfddon in wall)
Figure
2 -
Back View
~.I
,~-"~
!
I
<:~::-,:.
1' 1 1-' : -"' : ' - ' - """
' - --' - ' U
r "-"' " ' ' ' ' ." "
I I
(.
""";:':-;
Concealed Wiring
-
thidden in walt)
Receiver
~
. - - - . ' . ' , '
.:::-e!O
..
~
...
Surge Protector
Figure 3
Figure"