ADELSYSTEM ALL IN ONE CBI Series Manual del usuario - Página 5
Navegue en línea o descargue pdf Manual del usuario para UPS ADELSYSTEM ALL IN ONE CBI Series. ADELSYSTEM ALL IN ONE CBI Series 12 páginas.
Imprimir página
7.2 SELECT OUTPUT VOLTAGE (ONLY SIZE4 CBI280)
No.17: Caution: Switch off the system before Setting the Jumper. The Jumper is Read at the device
power-up only.
Output Voltage Selection
Output Voltage Selection
8 DRIVE AND MONITORING
8.1 FAULT - STATUS CONDITIONS (ISOLATED RELAY):
8.1.1 STATUS: Mains or Backup: Input Mains On/Off.
• No.5 Relay Contact: 5, 6, 7
• No.6: Led
8.1.2 FAULT: Low Battery, Battery Replacement, Faulty Battery or Faulty System
• No.4 Relay Contact: 8,9,10
• No.8: Led DIAGNOSIS: Battery charger mode, or, Diagnosis of the system through "blinking code"
Light signal
8.1.3 Back Up and Fault: Relay and LED Conditions
Relay:
ON
Mains Input
Vac
OFF
YES
Battery SOC
less than 30%
NO
Battery or
YES
system Fault?
NO
Note:
(1) Contact relay Mains/Back switch at least 5 seconds after disconnection of Power.
(2) See Diagnosis Led
8.1.4 Relay Contact Rating:
Max.DC1: 30 Vdc 1 A; AC1: 60 Vac 1A: Resistive load (EN 60947-4-1).Min.1mA at 5 Vdc: Min.
permissive load
8.1.5 Charging Mode STATUS
Status (Led)
Float
Charging
Absorption
Type
Boost
Recovery
8.1.6 Faulty Battery / Faulty System
Reverse polarity or high battery Voltage
(over 32.5Vdc for CBI 24xxA)
Battery No connected
Element in Short Circuit
Over Load or short circuit on the load
Bad battery; Internal impedance Bad or Bad battery wire
connection
Life test not possible
Boost condition; battery discharge after 4 min. of overload.
Internal fault
Low battery (under 18.5Vdc for CBI 24xxA) Only if started from
battery, no Mains input, from Jumper N°5 or Push Bottom
Master-Slave connection lost between the master and slave on
parallel configuration, (AP device only)
Bad battery wire connection; Parallel mode on Slave Device
Boost condition; battery discharge after 4 min. of overload;
Parallel mode on Slave Device
Port N°5 - Led N°6 Mains/Back-Up
5-6 Closed
5-7 Closed
■ - led off
■ - led On (1)
■ - led On
■ - led On
■ - led off
■ - led off
Jumper
24 Output Voltage
No Jumper
12 Output Voltage
Port N°4 - Led N°7 Fault Battery
8-9 Closed OK
8-10 Closed
■ - led off
■ - led off
■ - led On (2)
■ - led off
■ - led On
■ - led off
Diagnosis (No.8)
1 Blink/2 sec
1 Blink/sec
2 Blink/sec
5 Blink/sec
1 Blink/pause
2 Blink/pause
3 Blink/pause
4 Blink/pause
5 Blink/pause
6 Blink/pause
8 Blink/pause
9 Blink/pause
10 Blink/pause
11 Blink/pause
13 Blink/pause
15 Blink/pause
Fault
Battery
(No.7)
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON