Automated Logic S6104 Instrucciones técnicas - Página 3

Navegue en línea o descargue pdf Instrucciones técnicas para Unidad de control Automated Logic S6104. Automated Logic S6104 16 páginas.

Imprimir página

CAUTION Changes or modifications to this

unit not expressly approved by the party

responsible for compliance could void the

user's authority to operate equipment.

NOTE This equipment has been tested and

found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the

interference at his own expense.

Specifications

Power 24VAC ± 10%, 50-60Hz, 20VA

(0.83A) maximum (single Class 2 source

only, 100VA or less). (24VAC ± 10%, 60Hz

when ordered for UUKL Smoke Control

Systems.)

Inputs One LogiStat Port and 10 universal

inputs, configurable for 0-5VDC, 0-20mA,

or thermistor/dry contact.

NOTE Universal inputs 9 and 10 are

inaccessible if using a LogiStat or a

LogiStat Plus. Temperature and setpoint

adjust inputs replace universal inputs 9

and 10 in this situation.

Input Resolution 10 bit A/D.

Digital Outputs 6 digital outputs (Form

A), 3A max.

Analog Outputs 4 analog outputs (0 to

10VDC), 20mA source capability.

Output resolution 8 bit D/A.

Communication For WebCTRL, 156 kbps

BACnet-over-ARCNET and 9600 bps or

38.4 kbps EIA-485 BACnet MS/TP.

Revised 7/30/02 • S6104

For SuperVision, 156 kbps BACnet-over-

ARCNET, 9600 bps or 38.4 kbps legacy

Control Module network (CMnet). Access

Port: 9600 bps or 38.4 kbps EIA-485.

Environmental Operating Range -20°

to 150°F (-28.9° to 65.6°C); 10 to 90%

relative humidity, non-condensing.

When ordered for UUKL Smoke Control

Systems, 32°-120.2°F (0°-49° C); 10 to

85% relative humidity, non-condensing.

Status Indication Visual (LED) status of

communication, running, errors, and all

outputs.

Memory 512KB Flash memory and 512KB

non-volatile battery-backed SRAM, and

128 bytes of serial EEPROM.

Real Time Clock A battery-backed real

time clock that keeps track of time in the

event of a power failure.

Protection Built-in surge and transient

protection circuitry.

Battery Seven-year lithium BR2325 battery

provides a minimum of 10,000 hours of

data retention during power outages.

Listed by UL 916 (PAZX), cUL C22.2

No. 205-M1983 (PAZX7), FCC Part -

Subpart B - Class A.

Mounting

Screw the S6104 into an enclosed panel using

the mounting holes provided on the cover

plate. Be sure to leave about 2 inches (5

centimeters) on each side for wiring.

Addressing

Before setting or changing the address, make

sure the S6104's power is off. The S6104 only

reads the address when the module is turned

on. After changing the address, you must

transfer memory to the module. Refer to

"Transferring Memory" on page 14.