Automationdirect.com AcuAMP ACTS050 Series Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Transductor Automationdirect.com AcuAMP ACTS050 Series. Automationdirect.com AcuAMP ACTS050 Series 2 páginas.

Imprimir página

Specifications

Power Required

24 VAC/DC (+/-10%)

Power Consumption

< 2VA

Outputs

Solid state switch, N.O. and analog output

Switch Rating

1A @ 240VAC maximum

Offstate Leakage

< 10μA

0.50 sec. 5% over set point

Switch Response Time

0.20 sec. 50% over set point

0.15 sec. 100% over set point

Switch Hystersis

5% of setpoint

1-50 Amps (ACTS050)

Switch Setpoint Range

4-200 Amps (ACTS200)

Single turn potentiometer

Switch Setpoint Adjust

Setpoint displayed on sensor

1.1x range continuous

Sensed Current

3x range for 6 seconds

Limit

5x range for 1 second

Analog Output Signal

4-20mA

Analog Output

500Ω max

Impedance

< 0.30 sec. 90% step change

Analog Output Response

< 0.40 sec. 100% step change

Accuracy

+/-1%

Isolation Voltage

UL508, UL tested to 1480VAC

Frequency Range

40-400 Hz, Average Responding

Sensing Aperture

0.75 in (19mm) dia.

-Temp -4 to 122°F (-20 to 50°C)

-Humidity 0-95% RH, Non-condensing

Environmental

-Pollution degree 2

-Altitude 2000 meters

Case

UL 94V-0 Flammability rated thermoplastic

cULus listed E222847

Certifications

For products intended for the EU market, the

following is applicable to the CE compliance of

the product:

The ACTS050/ACTS200 Series may comply with EN 61010-1

CAT III 300V max line-toneutral measurement category. If

insulated cable is used for the primary circuit, the voltage rating

of the measurement category can be improved according to

the characteristics given by the cable manufacturer.

Use 24V input power and fuse at 5 amps. Power source

overvoltage category I as defined per EN 61010-1.

Part Number Key

ACTS 050 - 42 - AA - 24 - FD

CASE STYLE

FD - Fixed Core with setpoint display

POWER SUPPLY

24 - 24 VAC / DC

OUTPUT

AA - Normally Open

solid state switch

ANALOG OUTPUT

42 - 4 to 20 mA

RANGE

050 - 0-50 Amps AC (setpoint 1-50A)

200 - 0-200 Amps AC (setpoint 4-200A)

SENSOR TYPE

ACTS - AC current transducer and switch

Warning! Risk of hazardous voltage

When operating the device, certain parts may

carry hazardous live voltage (e.g., primary

conductor, secondary terminals). The device

should not be put into service if the installation is

not complete.

Warning! Risk of electric shock or

personal injury

Safe operation can only be guaranteed if the

device is used for the purpose for which it was

designed and within the limits of the technical

specifications. When this symbol is used, it

means you should consult all documentation to

understand the nature of potential hazards and

the action required to avoid them.

AutomationDirect.com (ADC)

3505 Hutchinson Road, Cumming, GA 30040

Phone: (800) 633-0405 or (770) 889-2858

ACTS - Inst - Rev 1

0820

P-N 893020015

ACTS050/ACTS200

SERIES

INSTALLATION

INSTRUCTIONS

Part No. ACTS050-42AA-24-FD

Quick Start Guide

1. Mount the sensor on a surface, if needed.

Run the wire to be monitored through the

aperture.

3. Connect output wiring.

a. Use 30-12AWG copper wire rated 75˚C min

and tighten terminals to 7 in-lbs.

b. Ensure the power supply voltage matches the

model you are installing.

c. Energize the power to the sensor.

Adjust setpoint.

a. LED will display the RMS value of AC current,

which will cause the output to change state.

b. Turn the potentiometer until your target

current value is displayed.

5. Analog signal output.

a. The analog output is powered from the sensor

power source.

b. The signal is proportional to the sensor range

selected.