Dynamite Prophet P1 Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Cargador de batería Dynamite Prophet P1. Dynamite Prophet P1 2 páginas. Mini ac battery charger

Imprimir página
Dynamite Prophet P1 Manual de instrucciones
STORAGE
14.8V (4S)
Prophet
™
14.8V (4S)
DISCHARGE
14.8V (4S)
Instruction Manual | Bedienungsanleitung | Manuel d'utilisation | Manuale di Istruzioni
DISCHARGE
14.8V (4S)
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole
discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and
click on the support tab for this product.
MEANING OF SPECIAL LANGUAGE
CHARGE
The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:
NT
2.0A
CHARGE
WARNING: Procedures, which if not properly followed, create the probability of property
damage, collateral damage, and serious injury OR create a high probability of superficial injury.
NT
2.0A
Auto CHARGE
CAUTION: Procedures, which if not properly followed, create the probability of physical property
damage AND possibility of serious injury.
NT
3.0A
Auto CHARGE
NOTICE: Procedures, which if not properly followed, create a possibility of physical property
damage AND little or no possibility of injury.
NT
3.0A
DISCHARGE
WARNING: Read the ENTIRE instruction manual to become familiar with the features of
the product before operating. Failure to operate the product correctly can result in
CUT: 3.2V
DISCHARGE
damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and
CUT: 3.2V
requires some basic mechanical ability. Failure to operate this Product in a safe and responsible
RE-PEAK
manner could result in injury or damage to the product or other property. This product is not
1
intended for use by children without direct adult supervision. Do not attempt disassembly, use
RE-PEAK
with INCompatible components or augment product in any way without the approval of Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is
1
CYCLE
essential to read and follow all the instructions and warnings in the manual, prior to assembly,
setup or use, in order to operate correctly and avoid damage or serious injury.
CHG
1
CYCLE
Age Recommendation: Not for children under 14 years. This is not a toy.
CHG
1
NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
DANGER: To reduce the risk of fire or electric shock, carefully follow these instructions.
ARGE
12.0V (6P)
ARGE
12.0V (6P)
SCHARGE
CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can
12.0V (6P)
cause fire, collateral damage and injuries.
SCHARGE
12.0V (6P)
CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.
CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge
programs will damage the battery or the charger.
0.00 0.00 V
V
0.00 0.00 V
PROGRAMMING QUICK START GUIDE
V
IN:
0.00V
0
L:0.00V
IN:
0.00V
1. Press ENTER / Start button to confirm you have read the manual and access the
charger functions.
0
L:0.00V
2. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC
RY CHECK
button to scroll through the main menu screens.
3. Press ENTER / Start to make a selection.
.............
RY CHECK
4. Press the DEC or INC button to scroll through the program options.
.............
IN:
0.00V
0
L:0.00V
IN:
0.00V
0
L:0.00V
BATT/PROGRAM
Li** BATT
BATT/PROGRAM
Ni** BATT
BATT/PROGRAM
Pb BATT
BATT/PROGRAM
BATT METER
BATT/PROGRAM
BATT RESISTANCE
© 2018 Horizon Hobby, LLC. Dynamite, Prophet , EC3 and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC.
All other trademarks, service marks and logos are property of their respective owners.
P1 Mini AC Battery Charger
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this product and comply with the
following warnings could result in product malfunction, electrical issues, excessive heat,
FIRE, and ultimately injury and property damage.
• NEVER LEAVE CHARGING BATTERIES UNATTENDED DURING USE.
• NEVER CHARGE BATTERIES OVERNIGHT.
• Never attempt to charge dead, damaged or wet battery packs.
• Never attempt to charge a battery pack containing different types of batteries.
• Never allow children under 14 years of age to charge battery packs.
• Never charge batteries in extremely hot or cold places or place in direct sunlight.
• Never charge a battery if the cable has been pinched or shorted.
• Never connect the charger if the power cable has been pinched or shorted.
• Never connect the charger to an automobile 12V battery while the vehicle is running.
• Never attempt to dismantle the charger or use a damaged charger.
• Never attach your charger to both an AC and a DC power source at the same time.
• Never connect the input jack (DC input) to AC power.
• Always use only rechargeable batteries designed for use with this type of charger in the correct
programming mode.
• Always inspect the battery before charging.
• Always keep the battery away from any material that could be affected by heat.
• Always monitor the charging area and have a fire extinguisher available at all times.
• Always end the charging process if the battery becomes hot to the touch or starts to change
form (swell) during the charge process.
• Always connect the charge cable to the charger first, then connect the battery to avoid short
circuit between the charge leads. Reverse the sequence when disconnecting.
• Always connect the positive red leads (+) and negative black leads (–) correctly.
• Always disconnect the battery after charging, and let the charger cool between charges.
• Always charge in a well-ventilated area.
• Always terminate all processes and contact Horizon Hobby if the product malfunctions.
• Charge only rechargeable batteries. Charging non-rechargeable batteries may cause the
batteries to burst, resulting in injury to persons and/or damage to property.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
WARNING: Never leave charger unattended, exceed maximum charge rate, charge with
non-approved batteries or charge batteries in the wrong mode. Failure to comply may
result in excessive heat, fire and serious injury.
CAUTION: Always ensure the battery you are charging meets the specifications of this
charger and that the charger settings are correct. Not doing so can result in excessive
heat and other related product malfunctions, which can lead to user injury or property damage.
Please contact Horizon Hobby or an authorized retailer with compatibility questions.
5. Press ENTER / Start to select a program option.
6. Press the DEC or INC Button to change the parameter. Press the ENTER / Start
Button again to move to the next parameter.
7. Once the parameters are at the desired settings, press and hold the ENTER /
Start Button for 3 seconds.
8. Press the Batt / PROG Stop Button at any time to stop charging.
Li** CHARGE
2.0A
14.8V (4S)
Li** FAST CHG
2.0A
14.8V (4S)
Li** STORAGE
2.0A
14.8V (4S)
Li** DISCHARGE
1.0A
14.8V (4S)
Ni** CHARGE
CURRENT
2.0A
Ni** Auto CHARGE
CURRENT
3.0A
Ni** DISCHARGE
1.0A
CUT: 3.2V
Ni** RE-PEAK
1
Ni** CYCLE
CHG>DCHG
1
Pb CHARGE
2.0A
12.0V (6P)
Pb DISCHARGE
1.0A
12.0V (6P)
0.00 0.00 0.00 V
0.00
V
MAIN:
0.00V
BATT/PROGRAM
H:0.00
L:0.00V
BATTERY CHECK
...................
MAIN:
0.00V
H:0.00
L:0.00V
BATT/PROGRAM
ON
Temp Cut-Off
On
Temp Cut-Off
On
Temperature Unit
Temperature Unit
Rest Time
Included Items
3
CHG>DCHG
Rest Time
AC Power Cord
Charge Adapter: Banana to EC3™ Device (DYNC0072)
CHG>DCHG
NiMH Sensitivity
D.Peak
Optional Items
NiMH Sensitivity
Temperature Sensor (DYN5033)
D.Peak
NiCd Sensitivity
Dynamite
®
LiPo Charge Bag: small (DYN1400), large (DYN1405)
D.Peak
NiCd Sensitivity
Specifications
Input Voltage 100–240V AC (50–60Hz); 11–18V DC
D.Peak
Key Beep
Charging Capability 2–4S Li-Po/Li-Ion/Li-Fe;
Buzzer
6–8C Ni-Cd/Ni-MH; 2–12V Pb
Key Beep
Battery Capacities 100–50000 mAh
Buzzer
Charge Current 0.1A–6A (in 0.1A Increments/60W max)
Bal. Connection
Discharge Current 0.10A–2.0A (in 0.1A Increments/10W max)
Bal. Connection
Balance Current 200mA max
Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV
Load Factory Set
Protection Short-circuit, over-current, reverse polarity, low input voltage,
over-temperature
Load Factory Set
Version
HW:1.00
Version
HW:1.00
BATT/PROGRAM
BATT MEMORY
BATT/PROGRAM
BATT MEMORY
A
[ BATT MEMORY X ]
ENTER SET->
[ BATT MEMORY X ]
B
ENTER SET->
G
BATT/PROGRAM
SYSTEM SETTING->
POWER UP SCREEN
DYNAMITE P1 MINI
DYNC3015
DYNAMITE P1 MINI
DYNC3015
When the charger is powered ON, there is a series of self tests and the charger will require the
user to verify they have read the manual by pressing the ENTER / Start button. The charger will
not proceed with charge functions until this process is completed.
READ THE MANUAL?
PRESS>TO CONFIRM
READ THE MANUAL?
PRESS>TO CONFIRM
LI-PO/LI-ION/LI-FE/LI-HV ARE SHOWN AS LI**.
MENUS DIFFER ONLY IN CELL AND PACK VOLTAGE VALUES.
LI** (LI-PO/LI-FE/LI-ION) LITHIUM CHARGING
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
positive and negative connectors match, red to red (positive to positive) and black to black
(negative to negative).
2. Connect the Balance Adapter Board to the Balance Port of the charge port (G,K).
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the balance adapter.
WARNING: Always use a balance connector when charging lithium batteries.
5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
BATT/PROGRAM
Li** BATT
BATT/PROGRAM
6. Press ENTER / Start
7. Press the DEC or INC Button to scroll through the program options (Charge, Balance Charge,
Storage, Discharge).
8. Press ENTER / Start to select a program option.
Li** CHARGE
2.0A
Li** FAST CHG
9. Press the DEC or INC Button to change the parameter. Press the ENTER / Start Button again
2.0A
to move to the next parameter.
10. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for
Li** BATT
3 seconds. Press ENTER / Start again to confirm and start the charge process.
Li** STORAGE
11. The charger will check the battery and charger settings and charging will begin. The charger
2.0A
will beep and display the following screen:
Li** BAL-CHG 3S
Li** DISCHARGE
C= 3200mAh
BATT/PROGRAM
1.0A
Ni** BATT
12. Press the DEC Button to see the rest of the Charging information.
13. Press the INC Button to see the voltages for each cell. Press ENTER / Start to return to the
BATT/PROGRAM
charging screen.
4.20 4.20 4.20
0.00 0.00 0.00
Ni** CHARGE
14. Press the Batt / PROG Stop Button at any time to stop charging.
CURRENT
15. When charging is complete, the charger will sound a series of beeps.
16. Disconnect the battery from the charger when the charge is complete.
Ni** Auto CHARGE
CURRENT
Ni** BATT
Ni** DISCHARGE
1.0A
5000mAh
50C 122F
50C 122F
Celcius
Celcius
10Min
10Min
CAUTION: Before charging, always ensure you have chosen the correct battery chemistry
type for the battery you are charging.
4mV
4mV
1. Connect the AC power cord to the charger AC Power Input Port.
2. Connect the AC power cord to the AC power source.
4mV
3. When the charger is powered ON, a message will appear on the LCD Screen.
4mV
CONNECTING BATTERIES TO THE CHARGER:
ON
CAUTION: Always power ON the charger before connecting a battery, or damage to the
ON
charger and the battery can result.
ON
1. Connect the charger to the power source.
ON
2. Select the charging settings.
3. Connect the banana plugs of the battery adapter cable to the Power Output, making sure that
ON
the positive and negative connectors are not reversed.
ON
4. Connect the battery connector to the battery adapter cable.
5. Start battery charging.
Enter
Enter
SW:1.03
SW:1.03
A. AC Power input Port
B. LCD Screen
C. Batt / PROG Stop
Not to scale.
D. DEC (decrease)
Not all wiring shown.
E. INC (increase)
Not all connectors shown.
F. ENTER / Start
C
D
E
F
H
I
J
K
OPERATING YOUR CHARGER
LI** (LI-PO/LI-FE/LI-ION) LITHIUM DISCHARGING
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
positive and negative connectors match, red to red (positive to positive) and black to black
(negative to negative).
2. Connect the Balance Port to the Balance Circuit Adapter Board (G,K).
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the Balance Adapter Board.
5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
6. Press the ENTER / Start Button.
7. the DEC or INC Button until Li-Po/Li-Ion/Li-Fe DCHG appears.
Li** DCHG
1.0A
8. Press the ENTER / Start Button to edit the parameter.
9. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for
3 seconds.
10. The charger will check the battery and charger settings and discharging will begin.
11. Press the DEC or INC Button to see the rest of the Discharging information.
12. Press Batt / PROG Stop at any time to stop discharging.
13. When discharging is complete, the charger will sound a series of beeps.
14. Disconnect the battery from the charger when the discharge is complete.
LI** (LI-PO/LI-FE/LI-ION) LITHIUM STORAGE CHARGING
Li** CHARGE
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
2.0A
14.8V (4S)
positive and negative connectors match, red to red (positive to positive) and black to black
(negative to negative).
Li** CHARGE
Li** FAST CHG
2. Connect the Balance Adapter Board to the Balance Port of the charge port (G,K).
3. Connect the battery connector to the battery adapter cable.
2.0A
2.0A
14.8V (4S)
4. Connect the balance connector of the battery to the balance adapter.
5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
Li** FAST CHG
Li** STORAGE
scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.
2.0A
6. Press the ENTER / Start Button.
2.0A
14.8V (4S)
7. The DEC or INC Button until Li-Po/Li-Ion/Li-Fe STORAGE appears.
Li** BATT
Li** STORAGE
Li** DISCHARGE
2.0A
1.0A
14.8V (4S)
Li** DISCHARGE
14.8V (4S)
8. Press the ENTER / Start Button to edit the parameter.
1.0A
9. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for
3 seconds. Press ENTER / Start again to confirm and start the process.
10. The charger will check the battery and charger settings and storage charging will begin.
14.8V (4S)
11. Press the DEC or INC Button to see the rest of the storage charging information.
12. Press Batt / PROG Stop at any time to stop charging.
Ni** CHARGE
13. When the storage process is complete, the charger will sound a series of beeps.
CURRENT
14. Disconnect the battery from the charger when the storage process is complete.
14.8V (4S)
Ni** CHARGE
Ni** Auto CHARGE
3.2A
CURRENT
CURRENT
14.8V (4S)
Ni** Auto CHARGE
Ni** DISCHARGE
CURRENT
1.0A
CUT: 3.2V
Ni** BATT
Ni** DISCHARGE
Ni** RE-PEAK
1.0A
Ni** RE-PEAK
Ni** CYCLE
2.0A
CHG>DCHG
Ni** CYCLE
3.0A
CHG>DCHG
CUT: 3.2V
DYNC3015
GETTING STARTED
G. Balance Board Connector
H. Charge Port
I. Temperature Sensor Port
J. USB/PC Link Port
K. Battery Adapter Cable
BATT TYPE
LiPo
BATT TYPE
LiPo
BATT VOLTAGE
14.8V(4S)
BATT VOLTAGE
14.8V(4S)
CHARGE CURRENT
2.0A
CHARGE CURRENT
2.0A
DISCHRG CURRENT
1.0A
DISCHRG CURRENT
1.0A
DISCHG VOLTAGE
3.0V/CELL
DISCHG VOLTAGE
3.0V/CELL
TVC=YOUR RISK!
Saftety Timer
4.20V
TVC=YOUR RISK!
ON
120Min
4.20V
SAVE PROGRAM
Capacity Cut-Off
ENTER
SAVE PROGRAM
ON
5000mAh
ENTER
Temp Cut-Off
On
50C 122F
Temperature Unit
Celcius
Rest Time
CHG>DCHG
10Min
NiMH Sensitivity
D.Peak
4mV
NiCd Sensitivity
D.Peak
4mV
3.0V
Key Beep
ON
9.0V(3S)
Buzzer
ON
Bal. Connection
ON
Load Factory Set
Enter
Version
HW:1.00
SW:1.03
BATT/PROGRAM
14.8V (4S)
BATT MEMORY
14.8V (4S)
[ BATT MEMORY X ]
ENTER SET->
14.8V (4S)
BATT/PROGRAM
SYSTEM SETTING->
14.8V (4S)
2.0A
2.0A
3.0A
3.0A
CUT: 3.2V
1
1
1
1