Dynamite Prophet P1 Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Ładowarka Dynamite Prophet P1. Dynamite Prophet P1 2 stron. Mini ac battery charger

Drukuj stronę

STORAGE

14.8V (4S)

Prophet

™

14.8V (4S)

DISCHARGE

14.8V (4S)

Instruction Manual | Bedienungsanleitung | Manuel d'utilisation | Manuale di Istruzioni

DISCHARGE

14.8V (4S)

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole

discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and

click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

CHARGE

The following terms are used throughout the product literature to indicate various levels of

potential harm when operating this product:

2.0A

CHARGE

WARNING: Procedures, which if not properly followed, create the probability of property

damage, collateral damage, and serious injury OR create a high probability of superficial injury.

2.0A

Auto CHARGE

CAUTION: Procedures, which if not properly followed, create the probability of physical property

damage AND possibility of serious injury.

3.0A

Auto CHARGE

NOTICE: Procedures, which if not properly followed, create a possibility of physical property

damage AND little or no possibility of injury.

3.0A

DISCHARGE

WARNING: Read the ENTIRE instruction manual to become familiar with the features of

the product before operating. Failure to operate the product correctly can result in

CUT: 3.2V

DISCHARGE

damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and

CUT: 3.2V

requires some basic mechanical ability. Failure to operate this Product in a safe and responsible

RE-PEAK

manner could result in injury or damage to the product or other property. This product is not

intended for use by children without direct adult supervision. Do not attempt disassembly, use

RE-PEAK

with INCompatible components or augment product in any way without the approval of Horizon

Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is

CYCLE

essential to read and follow all the instructions and warnings in the manual, prior to assembly,

setup or use, in order to operate correctly and avoid damage or serious injury.

CHG

CYCLE

Age Recommendation: Not for children under 14 years. This is not a toy.

CHG

NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

DANGER: To reduce the risk of fire or electric shock, carefully follow these instructions.

ARGE

12.0V (6P)

ARGE

12.0V (6P)

SCHARGE

CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can

12.0V (6P)

cause fire, collateral damage and injuries.

SCHARGE

12.0V (6P)

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge

programs will damage the battery or the charger.

0.00 0.00 V

PROGRAMMING QUICK START GUIDE

IN:

0.00V

L:0.00V

IN:

0.00V

1. Press ENTER / Start button to confirm you have read the manual and access the

charger functions.

L:0.00V

2. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC

RY CHECK

button to scroll through the main menu screens.

3. Press ENTER / Start to make a selection.

.............

RY CHECK

4. Press the DEC or INC button to scroll through the program options.

.............

IN:

0.00V

L:0.00V

IN:

0.00V

L:0.00V

BATT/PROGRAM

Li** BATT

BATT/PROGRAM

Ni** BATT

BATT/PROGRAM

Pb BATT

BATT/PROGRAM

BATT METER

BATT/PROGRAM

BATT RESISTANCE

All other trademarks, service marks and logos are property of their respective owners.

P1 Mini AC Battery Charger

CHARGING WARNINGS

WARNING: Failure to exercise caution while using this product and comply with the

following warnings could result in product malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED DURING USE.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never attempt to charge dead, damaged or wet battery packs.

• Never attempt to charge a battery pack containing different types of batteries.

• Never allow children under 14 years of age to charge battery packs.

• Never charge batteries in extremely hot or cold places or place in direct sunlight.

• Never charge a battery if the cable has been pinched or shorted.

• Never connect the charger if the power cable has been pinched or shorted.

• Never connect the charger to an automobile 12V battery while the vehicle is running.

• Never attempt to dismantle the charger or use a damaged charger.

• Never attach your charger to both an AC and a DC power source at the same time.

• Never connect the input jack (DC input) to AC power.

• Always use only rechargeable batteries designed for use with this type of charger in the correct

programming mode.

• Always inspect the battery before charging.

• Always keep the battery away from any material that could be affected by heat.

• Always monitor the charging area and have a fire extinguisher available at all times.

• Always end the charging process if the battery becomes hot to the touch or starts to change

form (swell) during the charge process.

• Always connect the charge cable to the charger first, then connect the battery to avoid short

circuit between the charge leads. Reverse the sequence when disconnecting.

• Always connect the positive red leads (+) and negative black leads (–) correctly.

• Always disconnect the battery after charging, and let the charger cool between charges.

• Always charge in a well-ventilated area.

• Always terminate all processes and contact Horizon Hobby if the product malfunctions.

• Charge only rechargeable batteries. Charging non-rechargeable batteries may cause the

batteries to burst, resulting in injury to persons and/or damage to property.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

WARNING: Never leave charger unattended, exceed maximum charge rate, charge with

non-approved batteries or charge batteries in the wrong mode. Failure to comply may

result in excessive heat, fire and serious injury.

CAUTION: Always ensure the battery you are charging meets the specifications of this

charger and that the charger settings are correct. Not doing so can result in excessive

heat and other related product malfunctions, which can lead to user injury or property damage.

Please contact Horizon Hobby or an authorized retailer with compatibility questions.

5. Press ENTER / Start to select a program option.

6. Press the DEC or INC Button to change the parameter. Press the ENTER / Start

Button again to move to the next parameter.

7. Once the parameters are at the desired settings, press and hold the ENTER /

Start Button for 3 seconds.

8. Press the Batt / PROG Stop Button at any time to stop charging.

Li** CHARGE

2.0A

14.8V (4S)

Li** FAST CHG

2.0A

14.8V (4S)

Li** STORAGE

2.0A

14.8V (4S)

Li** DISCHARGE

1.0A

14.8V (4S)

Ni** CHARGE

CURRENT

2.0A

Ni** Auto CHARGE

CURRENT

3.0A

Ni** DISCHARGE

1.0A

CUT: 3.2V

Ni** RE-PEAK

Ni** CYCLE

CHG>DCHG

Pb CHARGE

2.0A

12.0V (6P)

Pb DISCHARGE

1.0A

12.0V (6P)

0.00 0.00 0.00 V

0.00

MAIN:

0.00V

BATT/PROGRAM

H:0.00

L:0.00V

BATTERY CHECK

...................

MAIN:

0.00V

H:0.00

L:0.00V

BATT/PROGRAM

Temp Cut-Off

Temperature Unit

Rest Time

Included Items

CHG>DCHG

Rest Time

AC Power Cord

Charge Adapter: Banana to EC3™ Device (DYNC0072)

CHG>DCHG

NiMH Sensitivity

D.Peak

Optional Items

NiMH Sensitivity

Temperature Sensor (DYN5033)

D.Peak

NiCd Sensitivity

Dynamite

LiPo Charge Bag: small (DYN1400), large (DYN1405)

D.Peak

NiCd Sensitivity

Specifications

Input Voltage 100–240V AC (50–60Hz); 11–18V DC

D.Peak

Key Beep

Charging Capability 2–4S Li-Po/Li-Ion/Li-Fe;

Buzzer

6–8C Ni-Cd/Ni-MH; 2–12V Pb

Key Beep

Battery Capacities 100–50000 mAh

Buzzer

Charge Current 0.1A–6A (in 0.1A Increments/60W max)

Bal. Connection

Discharge Current 0.10A–2.0A (in 0.1A Increments/10W max)

Bal. Connection

Balance Current 200mA max

Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV

Load Factory Set

Protection Short-circuit, over-current, reverse polarity, low input voltage,

over-temperature

Load Factory Set

Version

HW:1.00

Version

HW:1.00

BATT/PROGRAM

BATT MEMORY

BATT/PROGRAM

BATT MEMORY

[ BATT MEMORY X ]

ENTER SET->

[ BATT MEMORY X ]

ENTER SET->

BATT/PROGRAM

SYSTEM SETTING->

POWER UP SCREEN

DYNAMITE P1 MINI

DYNC3015

DYNAMITE P1 MINI

DYNC3015

When the charger is powered ON, there is a series of self tests and the charger will require the

user to verify they have read the manual by pressing the ENTER / Start button. The charger will

not proceed with charge functions until this process is completed.

READ THE MANUAL?

PRESS>TO CONFIRM

READ THE MANUAL?

PRESS>TO CONFIRM

LI-PO/LI-ION/LI-FE/LI-HV ARE SHOWN AS LI**.

MENUS DIFFER ONLY IN CELL AND PACK VOLTAGE VALUES.

LI** (LI-PO/LI-FE/LI-ION) LITHIUM CHARGING

1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the

positive and negative connectors match, red to red (positive to positive) and black to black

(negative to negative).

2. Connect the Balance Adapter Board to the Balance Port of the charge port (G,K).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the balance adapter.

WARNING: Always use a balance connector when charging lithium batteries.

5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to

scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.

BATT/PROGRAM

Li** BATT

BATT/PROGRAM

6. Press ENTER / Start

7. Press the DEC or INC Button to scroll through the program options (Charge, Balance Charge,

Storage, Discharge).

8. Press ENTER / Start to select a program option.

Li** CHARGE

2.0A

Li** FAST CHG

9. Press the DEC or INC Button to change the parameter. Press the ENTER / Start Button again

2.0A

to move to the next parameter.

10. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for

Li** BATT

3 seconds. Press ENTER / Start again to confirm and start the charge process.

Li** STORAGE

11. The charger will check the battery and charger settings and charging will begin. The charger

2.0A

will beep and display the following screen:

Li** BAL-CHG 3S

Li** DISCHARGE

C= 3200mAh

BATT/PROGRAM

1.0A

Ni** BATT

12. Press the DEC Button to see the rest of the Charging information.

13. Press the INC Button to see the voltages for each cell. Press ENTER / Start to return to the

BATT/PROGRAM

charging screen.

4.20 4.20 4.20

0.00 0.00 0.00

Ni** CHARGE

14. Press the Batt / PROG Stop Button at any time to stop charging.

CURRENT

15. When charging is complete, the charger will sound a series of beeps.

16. Disconnect the battery from the charger when the charge is complete.

Ni** Auto CHARGE

CURRENT

Ni** BATT

Ni** DISCHARGE

1.0A

5000mAh

50C 122F

Celcius

10Min

CAUTION: Before charging, always ensure you have chosen the correct battery chemistry

type for the battery you are charging.

4mV

1. Connect the AC power cord to the charger AC Power Input Port.

2. Connect the AC power cord to the AC power source.

4mV

3. When the charger is powered ON, a message will appear on the LCD Screen.

4mV

CONNECTING BATTERIES TO THE CHARGER:

CAUTION: Always power ON the charger before connecting a battery, or damage to the

charger and the battery can result.

1. Connect the charger to the power source.

2. Select the charging settings.

3. Connect the banana plugs of the battery adapter cable to the Power Output, making sure that

the positive and negative connectors are not reversed.

4. Connect the battery connector to the battery adapter cable.

5. Start battery charging.

Enter

SW:1.03

A. AC Power input Port

B. LCD Screen

C. Batt / PROG Stop

Not to scale.

D. DEC (decrease)

Not all wiring shown.

E. INC (increase)

Not all connectors shown.

F. ENTER / Start

OPERATING YOUR CHARGER

LI** (LI-PO/LI-FE/LI-ION) LITHIUM DISCHARGING

1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the

positive and negative connectors match, red to red (positive to positive) and black to black

(negative to negative).

2. Connect the Balance Port to the Balance Circuit Adapter Board (G,K).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the Balance Adapter Board.

5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to

scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.

6. Press the ENTER / Start Button.

7. the DEC or INC Button until Li-Po/Li-Ion/Li-Fe DCHG appears.

Li** DCHG

1.0A

8. Press the ENTER / Start Button to edit the parameter.

9. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for

3 seconds.

10. The charger will check the battery and charger settings and discharging will begin.

11. Press the DEC or INC Button to see the rest of the Discharging information.

12. Press Batt / PROG Stop at any time to stop discharging.

13. When discharging is complete, the charger will sound a series of beeps.

14. Disconnect the battery from the charger when the discharge is complete.

LI** (LI-PO/LI-FE/LI-ION) LITHIUM STORAGE CHARGING

Li** CHARGE

1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the

2.0A

14.8V (4S)

positive and negative connectors match, red to red (positive to positive) and black to black

(negative to negative).

Li** CHARGE

Li** FAST CHG

2. Connect the Balance Adapter Board to the Balance Port of the charge port (G,K).

3. Connect the battery connector to the battery adapter cable.

2.0A

14.8V (4S)

4. Connect the balance connector of the battery to the balance adapter.

5. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to

Li** FAST CHG

Li** STORAGE

scroll through the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe.

2.0A

6. Press the ENTER / Start Button.

2.0A

14.8V (4S)

7. The DEC or INC Button until Li-Po/Li-Ion/Li-Fe STORAGE appears.

Li** BATT

Li** STORAGE

Li** DISCHARGE

2.0A

1.0A

14.8V (4S)

Li** DISCHARGE

14.8V (4S)

8. Press the ENTER / Start Button to edit the parameter.

1.0A

9. Once the parameters are at the desired settings, press and hold the ENTER / Start Button for

3 seconds. Press ENTER / Start again to confirm and start the process.

10. The charger will check the battery and charger settings and storage charging will begin.

14.8V (4S)

11. Press the DEC or INC Button to see the rest of the storage charging information.

12. Press Batt / PROG Stop at any time to stop charging.

Ni** CHARGE

13. When the storage process is complete, the charger will sound a series of beeps.

CURRENT

14. Disconnect the battery from the charger when the storage process is complete.

14.8V (4S)

Ni** CHARGE

Ni** Auto CHARGE

3.2A

CURRENT

14.8V (4S)

Ni** Auto CHARGE

Ni** DISCHARGE

CURRENT

1.0A

CUT: 3.2V

Ni** BATT

Ni** DISCHARGE

Ni** RE-PEAK

1.0A

Ni** RE-PEAK

Ni** CYCLE

2.0A

CHG>DCHG

Ni** CYCLE

3.0A

CHG>DCHG

CUT: 3.2V

DYNC3015

GETTING STARTED

G. Balance Board Connector

H. Charge Port

I. Temperature Sensor Port

J. USB/PC Link Port

K. Battery Adapter Cable

BATT TYPE

LiPo

BATT TYPE

LiPo

BATT VOLTAGE

14.8V(4S)

BATT VOLTAGE

14.8V(4S)

CHARGE CURRENT

2.0A

CHARGE CURRENT

2.0A

DISCHRG CURRENT

1.0A

DISCHRG CURRENT

1.0A

DISCHG VOLTAGE

3.0V/CELL

DISCHG VOLTAGE

3.0V/CELL

TVC=YOUR RISK!

Saftety Timer

4.20V

TVC=YOUR RISK!

120Min

4.20V

SAVE PROGRAM

Capacity Cut-Off

ENTER

SAVE PROGRAM

5000mAh

ENTER

Temp Cut-Off

50C 122F

Temperature Unit

Celcius

Rest Time

CHG>DCHG

10Min

NiMH Sensitivity

D.Peak

4mV

NiCd Sensitivity

D.Peak

4mV

3.0V

Key Beep

9.0V(3S)

Buzzer

Bal. Connection

Load Factory Set

Enter

Version

HW:1.00

SW:1.03

BATT/PROGRAM

14.8V (4S)

BATT MEMORY

14.8V (4S)

[ BATT MEMORY X ]

ENTER SET->

14.8V (4S)

BATT/PROGRAM

SYSTEM SETTING->

14.8V (4S)

2.0A

3.0A

CUT: 3.2V