Galaxy Aqua 9000 XP Manual de instrucciones de instalación - Página 4

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Productos de fontanería Galaxy Aqua 9000 XP. Galaxy Aqua 9000 XP 11 páginas. Pumped instantaneous electric shower

Imprimir página

1. Plumbing Connections

6. To enhance electrical safety a 30mA residual

current device (RCD) should be installed in all UK

electric and pumped shower circuits. This may be

part of the consumer unit or a separate unit.

7. Switch off immediately at isolating switch if water

ceases to flow during use.

8. Other electrical equipment i.e. extractor fans,

pumps must not be connected to the circuits within

the unit.

9. Switch off at isolating switch when not in use.

This is a safety procedure recommended with all

electrical appliances.

10. As with all electrical appliances it is

recommended to have the shower and installation

checked at least every two years by a competent

electrician to ensure there is no deterioration due to

age and usage.

SECTION

INTRODUCTION

This book contains all the necessary fitting

and operating instructions for your Galaxy

Aqua 9000 XP pumped electric shower.

Take time to read this book thoroughly

and familiarise yourself with all

instructions before commencing

installation. Please keep it for future

reference.

The shower installation must be carried

out by a competent person and in the

sequence of this instruction book.

Do not attempt any electrical or plumbing

work necessary to install this product

unless you have good practical

experience and adequate understanding

of the IEE regulations and water

regulations

Care taken during the installation will

ensure a long, trouble-free life from your

shower.

SPECIFICATIONS

Electrical

Nominal power rating at 240V

8.5kW - (40A MCB rating)

9.5kW – (40A MCB rating)

Nominal power rating at 230V

8.5kW - (40A MCB rating)

9.5kW – (40A MCB rating)

Water

Inlet connection – 15mm diameter.

Outlet connection – 1/2" BSP male thread.

Entry Points

Water and cable– bottom, top or back.

Materials

Backplate, cover, controls, sprayhead –

ABS.

Sprayplate – Acetal.

Elements – Minerally insulated corrosion

Resistant metal sheathing.

Dimensions

'XP'

Height 365 mm

Width 252 mm

Depth 107 mm

Standards and Approvals

Splashproof rating IPX4.

Complies with the requirements of current

British and European safety standards for

household and similar electrical

appliances.

Complies with requirements of the British

Electrotechnical Approvals Board (BEAB).

Meets with Compliance with European

SECTION

ADVICE TO USERS

The following points will help you

understand how the shower operates:

A. The electric heating elements operate

at a constant rate at your chosen power

setting. It is the flow rate of the water

Passing through the heater unit which

determines the shower temperature at

any given setting. (The slower the flow the

hotter the water becomes, and the faster

The flow the cooler the water).

B. During the Winter the Cold water supply

will be cooler than in the Summer months.

therefore, the temperature of the water

SECTION

ADJUSTING THE

SPRAYHEAD

Six sprayhead patterns are available.

Ajustment is by turning the bezel on the

sprayhead in either direction until the

dersired pattern is obtained.

Tranquil

Single outer spray

Fresh

Single Inner spray

Excite

Single Centre spray

Allure

Outer & Inner combined spray.

Sensual

Outer & Centre combined spray.

Ecstasy

Centre & Inner combined spray.

SECTION

SHOWERHEAD CLEANING

INSTRUCTIONS

IN SHOWER MAINTENANCE

To break away scale deposits on

a daily basis simply rub your

thumb over the rubber nipples

whilst the shower is running.

The showerhead should be cleaned

periodically to remove limescale or debris

which will reduce the performance of the

shower. The frequency of cleaning will

vary according to local water quality.

In hard water areas cleaning will be

needed more often than in soft water

areas. A liquid non-abrasive bathroom

cleaner may be used on external surfaces

of the handset.

1. Engage the key into the

spray cartridge recesses and

turn anti-clockwise to unscrew.

2. Remove the two small black

'O' rings from the rear of the

spray cartridge, and rinse 'O'

rings clean.

3. If deposits are stubborn,

immerse and soak the spray

cartridge for several hours in a

proprietary limescale remover.

Then with a small stiff bristled

brush scrub the spray cartridge.

4. Ensure all traces of limescale

and limescale remover are

rinsed off.

5. Throughly clean and rinse

the inside of the showerhead.

6. Replace the two black 'O'

rings on the rear of the spray

cartridge. A light smear of

petroleum jelly will ensure an

easy location into the grooves.

7. Refit cartridge to the

showerhead and tighten with

the spray key.