909 52299 Manual del usuario - Página 12

Navegue en línea o descargue pdf Manual del usuario para Inversor 909 52299. 909 52299 20 páginas. 3500w inverter generator with pure sine wave

Imprimir página

Engine Oil

• Check to ensure that the fuel drain (34) has been tightened and that fuel is

not leaking.

• Be careful not to admit dust, dirt, water or other foreign objects into the fuel.

• Wipe off spilt fuel thoroughly before starting engine.

• Ensure you DO NOT fuel the generator in close proximity to any open

flames, lit cigarettes, or hot objects.

• The generator should also be located in an open area with fresh air and NOT

in a confined area.

WARNING: Ensure the engine is switched off while undertaking

this task.

1. Remove the fuel tank cap (2) by rotating in an anticlockwise direction.

2. Remove the fuel tank inlet filter (27) and ensure it is clean and free of debris.

Check the level of fuel is sufficient.

3. If the fuel tank inlet filter (27) was removed to check the fuel level, ensure it

is replaced back before adding fuel.

4. To add fuel, pour the unleaded fuel from an approved fuel container into the

fuel tank (1). As fuel expands, DO NOT FILL to the lip of the tank. Maximum

fill is to the top of the fuel tank inlet filter (27) rim.

5. Replace fuel tank cap (2) turning in a clockwise direction to lock.

Checking the Engine Oil

The engine of this generator is NOT filled with oil when unpacked.

Prior to starting the engine ensure the oil tank is filled with SAE 10W-30

4 stroke oil. For the first time fill the engine should be filled with 600ml

of SAE 10W-30 oil.

NOTE: Damage to the engine is not covered under warranty if the engine is

run with insufficient oil.

1. Before checking or refilling oil, be sure the generator is put on a stable and

level surface, ensuring the engine has been switched OFF.

2. Remove the oil filler cap (15) by rotating the cap in an anti-clockwise

direction, and wipe all oil residue off the oil dipstick (15) with a clean rag.

Re insert the oil filler cap / dipstick (15) and thread the cap fully in position.

Then remove the oil filler cap / dipstick (15) by rotating in an anti clockwise

direction and view the oil level on the oil dipstick (15).

e-mail: [email protected]

MODEL: №. INF3800A • 52299

3500W Digital Inverter with Pure Sine Wave

AFTER SALES SUPPORT

1800 909 909

(toll free)

3500W Digital Inverter with Pure Sine Wave

3. If the oil level is close to or below the lower level line, refill with 4 stroke oil

to the upper level line (Fig O).

Do not use the generator when the oil level is close to the low level.

Fill the oil tank before use each time.

4. If the oil is contaminated or has discoloured, ensure you change

the oil. Replace the oil dipstick (15). DO NOT start the generator with the oil

dipstick (15) not firmly replaced.

NOTE: This engine is fitted with a

low oil indicator light (7). If the oil

level is too low the engine will stop

operating or the engine will not start.

It is advised to check the oil level

each time the generator is used and

fill to the upper mark on the oil

dipstick (15) by the above method.

Do NOT over fill.

Engine oil replacement

1. Place the generator on a flat and level surface and warm up the engine for

several minutes. Then stop the engine.

2. Place an oil pan under the generator and commence removing the oil drain

plug (16) by using a 10mm socket (not supplied), and rotating in an anti

clockwise direction to remove, so that the oil can be completely drained

from the oil tank (Fig P).

NOTE: Do not loose the small aluminium sealing washer on the thread of

the oil drain plug.

3. Check the oil drain plug (16), gasket washer, oil filler cap (15) and O-ring.

If these are damaged, have these replaced.

4. Reinstall the oil drain plug (16), and gasket washer

using a 10mm socket (not supplied), and rotating

in a clockwise direction until secure.

5. Refill with 4 stroke oil to the upper level line of the

oil dipstick (15) as detailed above.

CAUTION. Check that no foreign material, debris,

dust enters the crankcase.

6. Ensure to replace the oil filler cap (15).