activTek AP3000 Manual del usuario - Página 5

Navegue en línea o descargue pdf Manual del usuario para Limpiador de aire activTek AP3000. activTek AP3000 12 páginas. Portable whole home office system
También para activTek AP3000: Manual (16 páginas), Manual del usuario (12 páginas)

Imprimir página

SETTINGS AND ADJUSTMENTS

AP3000 by activTek can be turned on or off and adjusted

using the included remote .

If you are operating your central heating and

air conditioning fan or other ventilation system

continuously, set the coverage up to the total

ventilated indoor area. Otherwise, set the coverage up

to the size of the room. Do not exceed the size of the

ventilated indoor area when setting the purifier level.

Functions on Unit and Remote

Power (standby) Turns the unit ON and OFF.

Reminder Reset (control panel only)

Clears the maintenance reminders after performing

routine maintenance.

Functions on Remote Only

Fan Up/Fan Down Adjusts the five speed fan.

Away Mode

When the AP3000 is switched to the "Away Mode," the

Corona Discharge Ozone Plate is operated at maximum

output, which is 125% of the 3,000 square foot setting.

This mode is to be used only in unoccupied spaces; all

humans and pets should be removed from the area during

operation and for one hour after treatment completes or

until the ozone has sufficiently dissipated. For optimal

results, use the "Away Mode" to treat individual rooms

where the square footage is under 500 square feet, thereby

allowing the ozone level to sufficiently rise to treat the area

in the 2, 4, 6 or 8 hour programmed setting.

Normal Mode

When the AP3000 is operated in the "Normal Mode,"

ActivePure (RCI) Cell produces is a low level of Hydrogen

Peroxide gas (H2O2) and Super Oxides (O2-), as well as

positive and negative ionization which forms Hydroxyls.

In "Normal Mode", Ozone Free models will not produce

ozone, while Standard Cell models will produce very low

levels.

High Mode

When the AP3000 is switched to the "High Mode," the

Corona Discharge Ozone Plate becomes operational,

producing a low level of ozone based upon the area being

treated in square feet. The AP3000 is designed to produce

.03 to .045 parts per million (ppm) of ozone when the

square footage setting is equal to the ventilated area.

Purifier Up/Purifier Down (High Mode only)

Works when unit is in High Mode to set the purifier level for

the indoor area. The level is indicated by both a horizontal

bar graph and square footage (U.S. models) or square

meters (international models). The unit will switch to Normal

Mode, if the PURIFIER DOWN button is pressed when the

square footage is set to 250 ft

Display FT2 / M2 (remote control only)

Changes the purifier coverage shown on the LCD screen

from square feet to square meters.

*Please note: "unoccupied areas" includes pets. Some

pets, like humans, may experience adverse reactions from

exposure to increased levels of ozone and should not be

present during Away Mode operation.

(23 m

Power ON/OFF

Fan UP

Fan

DOWN

Normal/

High

LCD DISPLAY

The LCD Screen is used to display all current settings (see

page 4) as well as any maintenance reminders .

Fan Speed

Purifier Setting

Reminders

(normally blank - display will flash and reminders

appear here when unit needs maintenance)

LCD SCREEN BACKLIGHT

As adjustments are being made, the LCD screen backlight

will brighten and the settings on the screen will change .

After 3 seconds without change, the backlight will return

to normal .

If a maintenance reminder or a service reminder

appears, the backlight will brighten and constantly flash

until the Reminder Reset button is pressed or the service

problem is corrected.

A P 3 0 0 0

Reminder

Reset

Display FT

Purifier

DOWN

Away Mode

ON/SET/OFF

Battery

compartment

(2 AAA)

Purifier Coverage