HIKOKI GP 5V Manual de instrucciones de manipulación - Página 12

Navegue en línea o descargue pdf Manual de instrucciones de manipulación para Amoladora HIKOKI GP 5V. HIKOKI GP 5V 20 páginas. Electronic hand grinder

Imprimir página

HIKOKI GP 5V Manual de instrucciones de manipulación

Wheels for which the power tool was not designed cannot

be adequately guarded and are unsafe.

b) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-oﬀ wheel.

Abrasive cut-oﬀ wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

c) Always use undamaged wheel ﬂ anges that are of

correct size and shape for your selected wheel.

Proper wheel ﬂ anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-oﬀ

wheels may be diﬀ erent from grinding wheel ﬂ anges.

d) Do not use worn down wheels from larger power

tools.

Wheel intended for larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

GENERAL SAFETY INSTRUCTIONS FOR

GRINDERS

–

Check that speed marked on the wheel is equal to or

greater than the rated speed of the grinder;

–

Ensure that the wheel dimensions are compatible with

the grinder;

–

Abrasive wheels shall be stored and handled with care in

accordance with manufacturer's instructions;

–

Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

–

Ensure that mounted wheels and points are ﬁ tted in

accordance with the manufacturer's instructions;

SPECIFICATIONS

Model

Voltage (by areas)*

Power Input*

No-Load Speed*

Rated speed*

Max. Wheel Diam.*

Collet chuck Capacity**

Weight (without cord)

* Be sure to check the nameplate on product as it is subject to change by areas.

** This varies depending on the area.

Electronic Control

The grinder has an electronic speed control which provides:

○ full speed at all times in the range up to rated load.

○ soft-start.

○ variable speed

NOTE:

The grinder is equipped with a rotational speed control

circuit. The rotational speed may ﬂ uctuate slightly due to

the conditions of use and working voltage.

STANDARD ACCESSORIES

(1) Wrench (17 mm) ...........................................................1

(2) Wrench (12 mm) ...........................................................1

(3) Side handle (not included by areas) ..............................1

Standard accessories are subject to change without notice.

–

Ensure that blotters are used when they are provided

with the bonded abrasive product and when they are

required;

–

Ensure that the abrasive product is correctly mounted

and tightened before use and run the tool at no load

for 30 s in a safe position, stop immediately if there is

considerable vibration or if other defects are detected.

If this condition occurs, check the machine to determine

the cause;

–

If a guard is equipped with the tool never use the tool

without such a guard;

–

Do not use separate reducing bushings or adapters to

adapt large hole abrasive wheels;

–

For tools intended to be ﬁ tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to

accept the spindle length;

–

Check that the work piece is properly supported;

–

Do not use cutting oﬀ wheel for side grinding;

–

Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite ﬂ ammable

substances;

–

Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, ﬁ rst disconnect the tool from

the mains supply (use non metallic objects) and avoid

damaging internal parts;

–

Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves, helmet

and apron should be worn;

–

Pay attention to the wheel that continues to rotate after

the tool is switched oﬀ .

GP3V

(110 V, 120 V, 127 V, 220 V, 230 V, 240 V)

7000 – 29000 /min

30800 /min

25 mm

6 mm

1.8 kg

OPTIONAL ACCESSORIES (sold separately)

○ Collet chuck

for 3 mm shaft

for 3.175 mm (1/8") shaft

for 6.35 mm (1/4") shaft

for 8 mm shaft

Dimensions and handling methods other than the shaft

hole are the same as those for the 6 mm collet chuck.

○ Wheels with 6 mm shaft

All wheels are provided with WA grain, 60 granding,

and P bonding and are suitable for grinding general and

special steel materials.

GP5V

760 W

2000 – 8300 /min

8820 /min

50 mm

6 mm

1.9 kg