HIKOKI GP 5V Taşıma Talimatları Kılavuzu - Sayfa 12
Öğütücü HIKOKI GP 5V için çevrimiçi göz atın veya pdf Taşıma Talimatları Kılavuzu indirin. HIKOKI GP 5V 20 sayfaları. Electronic hand grinder
Sayfayı Yazdır
Wheels for which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may cause
them to shatter.
c) Always use undamaged wheel fl anges that are of
correct size and shape for your selected wheel.
Proper wheel fl anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be diff erent from grinding wheel fl anges.
d) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
GENERAL SAFETY INSTRUCTIONS FOR
GRINDERS
–
Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder;
–
Ensure that the wheel dimensions are compatible with
the grinder;
–
Abrasive wheels shall be stored and handled with care in
accordance with manufacturer's instructions;
–
Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
–
Ensure that mounted wheels and points are fi tted in
accordance with the manufacturer's instructions;
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input*
No-Load Speed*
Rated speed*
Max. Wheel Diam.*
Collet chuck Capacity**
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
** This varies depending on the area.
Electronic Control
The grinder has an electronic speed control which provides:
○ full speed at all times in the range up to rated load.
○ soft-start.
○ variable speed
NOTE:
The grinder is equipped with a rotational speed control
circuit. The rotational speed may fl uctuate slightly due to
the conditions of use and working voltage.
STANDARD ACCESSORIES
(1) Wrench (17 mm) ...........................................................1
(2) Wrench (12 mm) ...........................................................1
(3) Side handle (not included by areas) ..............................1
Standard accessories are subject to change without notice.
11
–
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required;
–
Ensure that the abrasive product is correctly mounted
and tightened before use and run the tool at no load
for 30 s in a safe position, stop immediately if there is
considerable vibration or if other defects are detected.
If this condition occurs, check the machine to determine
the cause;
–
If a guard is equipped with the tool never use the tool
without such a guard;
–
Do not use separate reducing bushings or adapters to
adapt large hole abrasive wheels;
–
For tools intended to be fi tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to
accept the spindle length;
–
Check that the work piece is properly supported;
–
Do not use cutting off wheel for side grinding;
–
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite fl ammable
substances;
–
Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, fi rst disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts;
–
Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves, helmet
and apron should be worn;
–
Pay attention to the wheel that continues to rotate after
the tool is switched off .
GP3V
(110 V, 120 V, 127 V, 220 V, 230 V, 240 V)
7000 – 29000 /min
30800 /min
25 mm
6 mm
1.8 kg
OPTIONAL ACCESSORIES (sold separately)
○ Collet chuck
for 3 mm shaft
for 3.175 mm (1/8") shaft
for 6.35 mm (1/4") shaft
for 8 mm shaft
Dimensions and handling methods other than the shaft
hole are the same as those for the 6 mm collet chuck.
○ Wheels with 6 mm shaft
All wheels are provided with WA grain, 60 granding,
and P bonding and are suitable for grinding general and
special steel materials.
GP5V
760 W
2000 – 8300 /min
8820 /min
50 mm
6 mm
1.9 kg