Decko 24000-DKO Manual del usuario - Página 8

Navegue en línea o descargue pdf Manual del usuario para Abrepuertas de garaje Decko 24000-DKO. Decko 24000-DKO 14 páginas. Handles doors 18 ft. wide & up to 7ft.tall

Imprimir página

1. Operating the Opener

Attaching Rail to Header Bracket and Mounting Door Bracket

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- REINFORCEMENT is recommended for fiberglass, aluminum or lightweight steel garage doors BEFORE

installing the door Bracket. Contact your door manufacturer for reinforcement options.

Carton

Hitch Pin

Clevis Pin - 5/16" x 1-1/2"

Fig.1

2-4" (5-10cm)

Vertical Centerline of Door

Self-Threading

Screw - 1/4" x 5/8"

Fig.2

CAUTION

To Attach the Opener to the Header Bracket

As shown in Fig.1, use the packaging carton as temporary

support for the Opener. Place the Opener on carton to

prevent damage.

Align the mounting hole on the header rail to the mounting

hole on the Header Bracket.

Connect the Header Rail and the Door Bracket together

with a 5/16" x 1-1/2" Clevis Pin and lock it in place with a

Hitch Pin.

To mount the Door Bracket

Note: Some door reinforcement kits may provide direct

attachment of the door arm to the reinforcement bracket. If you

have a door reinforcement bracket with this option, skip this step

and proceed with the next step "Mounting Opener to Ceiling".

Position the Door Bracket on the centerline of the door

approximately 2" - 4" (5-10cm) below the top edge of the

door, as shown in Fig.2.

Depending on the construction of your door, install using

one of the steps shown if Fig. 3 below:

For steel / lightweight doors with vertical steel

reinforcements / factory reinforced.

(a) Mark and drill two 3/16" holes. Make sure not to drill

through the garage door. Secure the Door Bracket with two

1/4" x 5/8" Self-Threading Screws (provided) as shown in

Fig.3(a).

(b) Alternative installation: Drill two 5/16" holes through the

door. Secure the Door Bracket using two 5/16" Bolts, lock

washers and nuts (not provided) as shown in Fig.3(b). The

length of bolts will depend on the thickness of your door.

Wood door

Secure the Door Bracket using two 5/16" carriage bolts,

washers and nuts (not provided) as shown in Fig.3(c). The

length of bolts will depend on the thickness of your door.

Note: DO NOT use Self-Threading Screws on a wood door.

(a)

(b)

Fig.3

Door Status vs. Activation

Door at fully open / close position

Door is closing

Door is opening

Door is stopped as intended in partially open position

Door is obstructed while closing

Door is obstructed while opening

Door is fully opened and Photo Eye System is obstructed

Courtesy Light Responses

Opener is initially plugged-in / Power restored

Upon Opener activation

"LEARN" button is pressed

Remote Transmitter / Keyless Entry PIN code accepted

The Photo Eye System is obstructed during door-closing or

door is obstructed during opening

Opener motor overheat (Thermal Protection)

Manual Operation

To Prevent SERIOUS INJURY or DEATH:

- Use Emergency Release to disconnect Trolley ONLY when the door is CLOSED to prevent unexpected rapid falling in

case of a unbalanced / poor-conditioned door.

- Use Emergency Release ONLY when doorway is clear of persons and obstructions.

- DO NOT use Emergency Release to pull the door open or closed.

DISCONNECT

(c)

Door status

Door will move to fully close / open position

Door will reverse

Door will stop

Door will reverse while flashing courtesy light

Door will stop

Door will not close

Operation / Condition

Flashes twice

Turns on for 3-1/2 minutes and turns off automatically

Turns on for 30 seconds

Flashes twice

Flashes for 30 seconds (Re-align and clear obstruction)

Flashes 5 times (Wait about 15 minutes to cool down)

WARNING

In case of a power failure or door obstruction, PULL

EMERGENCY Knob to release door from Opener.

Lever

To Disconnect Trolley for Manual Operation

With the door closed, pull down the emergency release knob to

CONNECT

the DISCONNECT position. The door can be raised / lowered

manually.

To Re-connect Trolley

Flip to reconnect

Pull the knob toward the Opener so that the lever will flip up to

the CONNECT position. The Trolley will reconnect itself when

the Opener is activated or when the door is manually opened/

Pull to Disconnect

closed

Activation using Push Button / Transmitter

Courtesy Light Response