KitchenAid KICU540BSS Manual de instrucciones de instalación - Página 3

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Placa de cocción KitchenAid KICU540BSS. KitchenAid KICU540BSS 12 páginas. Electric induction cooktop

Imprimir página

Cabinet Dimensions

IMPORTANT: If you are installing a range hood or microwave

hood combination above the range, follow the range hood or

microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A. 23½" (60.0 cm)

B. Combustible area above countertop (shown by dashed box above)

C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet, (24" [61 cm]

minimum clearance if bottom of wood or metal cabinet is covered by

¹⁄₄

not less than

" [0.6 cm] flame retardant millboard covered with not

less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or

0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)

D. 13" (33.0 cm) recommended upper cabinet depth

E. 2" (5.1 cm)

¹⁄₁₆

F. 19¼" ±

" (49.0 ± 0.16 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet; 12" (30.5 cm) minimum clearance from bottom

of countertop

I. Junction box or outlet; 10" (25.4 cm) from right-hand side of cabinet

¹⁄₁₆

J. 22

" ±

" (56.0 ± 0.16 cm)

K. 4" (10.0 cm) minimum clearance to nearest left and right side

combustible surface above cooktop

L. 2" (5.1 cm) minimum clearance between back wall and countertop

M. IMPORTANT: For proper ventilation, provide a vent of

under the countertop, in the front of the cabinet. The ventilation

opening is to extend the full length of the cooktop cutout. See the

following illustration.

³⁄₁₆"

(5.0 mm)

³⁄₁₆

" (5 mm)

NOTES: After you make the countertop cutout, some

installations may require notching down the base cabinet side

walls to clear the cooktop base. To avoid this modification, use a

base cabinet with sidewalls wider than the cutout.

If the cabinet has a drawer, a 5¹⁄₈" (13 cm) depth clearance from

the countertop to the top of the drawer (or other obstruction) in

the base cabinet is required.

Electrical Requirements

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground cooktop.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

cooktop is properly grounded.

It is not recommended to have a fuse in the neutral or ground

circuit.

Make sure that the electrical connection and wire size are

adequate and in conformance with the CSA Standards C22.1-94,

Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest

edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

CSA International

178 Rexdale Boulevard

Toronto, Ontario

Canada M9W 1R3

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only

electrical supply is required on a separate circuit, fused on

both sides of the line.

The cooktop should be connected directly to the junction box

through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse

box or circuit breaker box should be connected directly to the

junction box.