KitchenAid 30" and 36" Retractable Downdraft Vent Systems Manual de instrucciones de instalación - Página 3

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Campana de ventilación KitchenAid 30" and 36" Retractable Downdraft Vent Systems. KitchenAid 30" and 36" Retractable Downdraft Vent Systems 9 páginas. 30” and 36” retractable downdraft vent systems

Imprimir página

Electrical

requirements

Before you

start...

Injury Hazard

To eliminate

the risk of burns or fire,

avoid installing

cabinet storage above

the cooking

surface.

If cabinets

are

already installed,

avoid the use of

cabinets

while cooktop

is in use.

Reaching

over a heated cooking

surface could result in a serious

burn.

Use two or more people to move and

install downdraft

vent.

Failure to follow these instructions

can

result in back or other injury.

Important:

Observe all governing

codes

and ordinances.

Proper installation

is your responsibility.

Make sure you have everything

necessary

for correct installation.

It is the responsibility

of the installer to comply with the installation

clearances specified on the model/serial

rating plate. The model/serial

rating plate is

located on the front of the downdraft vent

above the wiring box cover.

Check location

where downdraft vent will

be installed. The location should be away

from strong draft areas, such as windows,

doors and strong heating vents or fans.

Before making countertop cutout, check that

downdraft vent and cooktop location will

clear cabinet walls, backsplash, and rear

wall studs inside cabinet.

ALL OPENINGS

IN THE WALL OR

FLOOR WHERE RETRACTABLE

DOWNDRAFT

VENT IS TO BE

INSTALLED

MUST BE SEALED.

Electrical

ground

is required. See

"Electrical requirements,"

Panel B.

When installing retractable downdraft vent,

the cabinet drawer will need to be removed

and the drawer front installed permanently

to cabinet.

30" min. base cabinet

is required. If

cabinet has a drawer, 3-l/2" depth

clearance from the countertop to the top of

the drawer (or other obstruction

in the base

cabinet) is required.

Note: Downdraft vent is installed directly

behind the cooktop. Install downdraft vent

first.

Downdraft

vent is not approved

for use

in mobile homes.

Cabinet construction:

Downdraft vent is

designed for use in a cabinet with a depth of

24". The maximum depth of the overhead

cabinet is 13". Overhead cabinets installed

at either side of the downdraft vent must be

18" above the cooking surface. See cook-top

Installation

Instructions for the minimum

distance between the front edge of the

countertop and front edge of cooktop. The

minimum horizontal distance between the

overhead cabinets is the same as the width

of the installed downdraft vent.

When installing a 36" retractable downdraft

vent with three "Create-A-Cook-top"

modules, the optional support must be

installed on the front of the downdraft vent.

See installation steps for details.

Electrical Shock Hazard

Electrically

ground downdraft

vent.

Failure to follow this instruction

could

result in death, fire or electrical

shock.

If codes permit and a separate

grounding

wire is used, it is recommended

that a

qualified

electrician

determine

that the

grounding

path is adequate.

Do Not ground to a gas pipe.

Check with a qualified

electrician

if you are

not sure the downdraft

vent is properly

grounded.

Do Not have a fuse in the neutral or

grounding

circuit.

IMPORTANT:

Save Installation

Instructions

for electrical

inspector's

use.

Electrical

Shock Hazard

Check for electrical

wires that may be

concealed

behind wall covering

before

drilling

holes into wall.

Do not use downdraft

vent solid state

fan speed control

device.

Failure to follow these instructions

could result in death, fire or electrical

Lshock.

It is the customer's

responsibility:

To contact

a qualified

electrical

installer.

To assure that electrical

installation

adequate

and in conformance

with

National

Electrical

Code, ANSVNFPA

70 - latest edition*,

and local codes

and ordinances.

IA.I

A 120.volt, 60.Hz, AC-only

electrical supply is required on a

separate 15ampere

circuit, fused on both

sides of the line. A time-delay fuse or circuit

breaker is recommended.

The fuse must be

sized per local codes in accordance with the

electrical rating of the downdraft vent as

specified on the model/serial

rating plate

located on the front of the downdraft vent

above the wiring box cover.

Tools needed for

installation:

8mm

or power

318" nut

supply

driver or

cable

ratchet

le(

THE RETRACTABLE

DOWNDRAFT

VENT MUST BE

CONNECTED

WITH COPPER WIRE ONLY

. Wire sizes must conform to the

requirements

of the National

Electrical Code, ANSIINFPA

70 -

latest

edition*, and all local codes and

ordinances.

Wire size and connections

must

conform with the rating of the downdraft

vent.

Copies of the standard listed above may be

obtained from:

* National

Fire Protection

Association

Batterymarch

Park

Quincy,

Massachusetts

02269

sabe

Phillips

screwdriver

mIm.-YIaYI

screwdriv

WARNING -TO

REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

A. Installation

Work And Electrical

Wiring Must Be Done By Qualified

Person(s) In Accordance

With All

Applicable

Codes And Standards,

Including

Fire-Rated Construction.

B. The combustion

airflow needed for

safe operation

of fuel-burning

equipment

may be affected by this

unit's operation.

Follow the heating

equipment

manufacturer's

guideline

and safety standards

such as those

published

by the National Fire

Protection

Association

(NFPA), and

the American Society for Heating,

Refrigeration

and Air Conditioning

Engineers

(ASHRAE), and the local

code authorities.

C. When cutting or drilling

into wall or

ceiling, do not damage electrical

wiring and other hidden utilities.

D. Ducted fans must always be vented to

the outdoors.

E. If this unit is to be installed

over a tub

or shower, it must be marked as

appropriate

for the application.

(DI

This downdraft vent should be

connected directly to the fused

disconnect

(or circuit breaker) through

flexible, armored or non-metallic

sheathed,

copper cable. Allow some slack in the cable

so the downdraft vent can be moved if

servicing is ever necessary.

IEl

~ A U.L.-listed, l/2" conduit

connector must be provided at

each end of the power supply cable (at the

downdraft vent and at the junction box).

IFI

A wiring diagram is located on the

downdraft vent base above the

wiring box cover.

'arts supplied

'or installation:

Electrical

connection

1. Cut a 1 -l/2" hole in floor or side of

cabinet for power supply wire. The hole

cut for electrical wiring through a wood

cabinet should be sanded until smooth.

A grommet (Part No. 302797) must cover

the hole cut for the electrical wiring

through a metal cabinet.

2. Run flexible armored or nonmetallic

sheathed copper cable from fused

disconnect circuit breaker or junction box

through the cabinet hole to the downdraft

vent location.

3. See installation

steps to connect power

supply cable to downdraft vent.

2 end caps

2 lower support

legs

2 overcounter

mounting

brackets

2 undercounter

mounting

brackets

1 bag of fasteners

1 metal cover

1 backdraft

damper

literature

package

optional

support

and

two screws

(36"

models only)

Parts needed

for installation:

Fire Hazard

Do Not obstruct

the flow of

combustion

and ventilation

air.

Failure to follow this instruction

could

result in fire.

2 conduit

connectors

1 wall cap for interior-mounted

motor

ductwork

Panel B