Gardena WP 600 Instrucciones de uso - Página 5

Navegue en línea o descargue pdf Instrucciones de uso para Bomba de agua Gardena WP 600. Gardena WP 600 8 páginas. Fountain pump 12 v
También para Gardena WP 600: Manual de instrucciones (8 páginas), Manual del usuario (6 páginas), Manual de instrucciones (7 páginas)

Imprimir página

Operation

Installing the pump

1. Remove the pump from the filter basket and screw the regulator

supplied onto the second opening of the pump up to the limit

stop (➔ max. delivery capacity on the vertical outlet). Then

replace the pump in the filter basket.

2. Put the pump on a stable base to ensure that the upper edge of

the filter tank is completely immersed in water.

Pay attention to

Please note the maximum submersion depth (see "Technical Data").

minimum water depth

Finding a location

GARDENA lightline Transformers are licensed for outdoor use.

for the transformer

You may attach them to the ground or the wall.

When attaching to the wall, please take care that the connection

sockets are pointing towards the ground.

When attaching to the ground, please take care that the trans-

former is not exposed to direct rainfall or to a mechanical

hazard.

2 m

Starting the pump

Put the plug connection into a free socket of the transformer

and connect the power cable of the transformer with a 230 V AC

socket.

Caution! Pump will start running immediately!

Avoid dry operation

Avoid dry operation of the pump as dry running will produce

undesirable heat and destroy the pump.

Horizontal or

Loosen the regulator by turning it anti-clockwise until you

second outlet

achieve the desired water flow from the vertical pipe of the

fountain / water feature.

You may connect other terminals to the second outlet.

For example, a separately installed water jet may be operated

via the GARDENA light jet base, Art. No. 7886. If necessary

fix the light jet base with two screws.

Information:

This significantly reduces the volume of the vertical water jet.

If the max. delivery capacity of the second outlet is to be used

then the vertical outlet should be closed with the end cap sup-

plied.

Example:

Hose pipe connection with the GARDENA light jet base

We recommend the use of a 3 /4" (19 mm) GARDENA pond

hose pipe, Art. No. 7895, connected to with the GARDENA

"Profi" Maxi-Flow-System with Tap Connector (Art. No. 2801

and 2802) and the GARDENA "Profi" Maxi-Flow-System Hose

connectors (Art. No. 2817).

Care instructions

Cleaning the filter tank

Filter tank and pump should be free from dirt particles!

How to clean :

Pull the plug connections out of the transformer and disconnect

its power plug!

Remove the pump from the water.

If necessary remove the gravel.

Clean the pump and the filter using a water jet.

If there are deposits of dirt inside the pump then dismantle the

casing (➔ ➔ see „Dismantling") and carefully clean the interior

fittings with water.

Information: Do not use any hard objects or strong detergents!

Blocked feed impeller

If the feed impeller becomes blocked, the pump and the filter

should be cleaned (see above).

Dismantling

1. Pull the plug connections out of the transformer and disconnect

its power plug!

2. Remove the pump from the water.

3. If necessary remove the gravel.

4. Pull the pump pointing vertically upwards out of the filter tank.

Then assemble all the fittings reversing the order and direction

in which they were dismantled. Please take care that the seal

ring

➔ Make sure while assembling that you attach the pump casing

with the pressure joint being cated, press it firmly and then

turn it straight to the right.

➔ Observe the markings.

5. Pull the suction filter casing

wards and remove it.

6. Remove the foam filter

from the

suction piece of the pump.

7. Turn the pump casing

to the left

to the limit stop and then pull it straight

towards the front and remove it!

Do not tilt!

8. Pull the feed impeller

out of the

motor casing

is properly re-fitted.

for-