Aqua Pulse Spas AIRLIE LUXURY SPA Instrucciones - Página 4
Navegue en línea o descargue pdf Instrucciones para Bañera de hidromasaje Aqua Pulse Spas AIRLIE LUXURY SPA. Aqua Pulse Spas AIRLIE LUXURY SPA 5 páginas.
Imprimir páginaHOW TO BALANCE CALCIUM HARDNESS ideal reading is between 250-400ppm.
If your reading is lower than 250ppm raise the Calcium Hardness by adding
Hardness Raiser #11.
7g will raise the Calcium Hardness by approximately 10ppm.
Do not use any brand of Test Strips to balance Calcium Hardness.
To balance your Calcium Hardness, you will need to take a sample of your spas water into a pool or spa store for
accurate testing. When you apply the Calcium Hardness required this may make your water go cloudy, don't panic it
will clear up in a couple of days.
Example reading is 200ppm and I want to get close to 325ppm
325ppm – 200ppm = 125ppm ÷ 10ppm = 12.5 x 7g = 87.5g to apply
Use a bucket and scoop some of the spas water into the bucket until it is roughly ¾ full, then add the Hardness Raiser
#11 to the bucket of water and stir (avoid contact with your skin), when completely dissolved (this may take several
hours) pour the water from the bucket into the spa and run jet 1 for 5 minutes.
Do not use any brand of Test Strips to balance Calcium Hardness.
To balance your Calcium Hardness, you will need to take a sample of your spas water into a pool or spa store for
accurate testing. When you apply the Calcium Hardness required this may make your water go cloudy, don't panic it
will clear up in a couple of days.
If your reading is
higher than 400ppm
lower the Calcium Hardness by adding
Calcium Remover.
2.1ml will lower the Calcium Hardness by approximately 10ppm.
Example reading is 450ppm and I want to get close to 325ppm.
450ppm – 325ppm = 125ppm ÷ 10ppm = 12.5 x 2.1ml =26.25ml to apply.
Add straight into the spas water away from the filter box and run jet 1 for 5 minutes to mix it in.
EVERY 6 MONTHS PIPE FLUSH & DRAIN THE WATER
NEVER DRAIN YOUR SPA IN DAYLIGHT HOURS YOU MUST ALWAYS DRAIN YOUR SPA AT NIGHT-TIME AND
REFILL YOUR SPA THE SAME NIGHT.
An empty or partially empty spa of water during sunlight hours can cause deforming, melting, crazing, discolouration,
blisters or holes in the spa's fiberglass, acrylic and fittings, this can happen within minutes of the spa being emptied or
partially empty. Your warranty does not cover deforming, melting, crazing, discolouration, blisters or holes in the spa's
acrylic and fittings, so it is especially important your hardcover is on the spa when not in use and the spa is always
filled with water during daylight hours.
To drain your spa add some water so that the water is higher than the normal water line this will help to clean off
chemical residue which can build up at the water line. Now put 1 Litre of Spa Pipe Flusha #12 into the water and run
all pumps for at least 20 minutes, then turn the power supply to the spa off and drain the water. Place your garden
hose in each jet and flush out any residue left in the pipes. Sponge out any remaining water in the spa, wipe down the
complete shell with a soft cloth, do not use any chemicals. Pipe Flusha cleans your spas pumps & heater which helps
prevent premature failure of these parts.
When refilling the spa make sure that the drain has been closed and place the hose in the filter box to refill the spa
with water. Do not forget to remove the fitting off the hose.
Visit: www.aquapulsespas.com.au