Panasonic PT-L520E Manual de instrucciones - Página 11
Navegue en línea o descargue pdf Manual de instrucciones para Proyector Panasonic PT-L520E. Panasonic PT-L520E 30 páginas. Lcd projector
Imprimir página
Inserting the batteries
# Open the cover.
$ Insert the batteries so that the
polarities are correct, and then close the
cover.
AAA batteries
(two)
NOTE:
B Do not drop the remote control unit.
B Do not drop the remote control unit.
B Keep the remote control unit away from liquids.
B Keep the remote control unit away from liquids.
B Remove the batteries if not using the remote control unit for long periods.
B Remove the batteries if not using the remote control unit for long periods.
B Do not use rechargeable batteries.
B Do not use rechargeable batteries.
Operating range
If the remote control unit is held so
that it is facing directly in front of the
remote control signal receptors on
the front or rear of the projector, the
operating range is within
approximately 7 m (23´) from the
surfaces of the receptors.
Furthermore, the remote control unit
can be operated from an angle of
±30° to the left or right and ±15°
above or below the receptors.
20-E
NGLISH
NOTE:
B If there are any obstacles in between
B If there are any obstacles in between
the remote control unit and the
the remote control unit and the
receivers, the remote control unit may
receivers, the remote control unit may
not operate correctly.
not operate correctly.
B If strong light is allowed to shine onto
B If strong light is allowed to shine onto
the remote control signal receiver,
the remote control signal receiver,
correct remote control operation may
correct remote control operation may
not be possible. Place the projector as
not be possible. Place the projector as
far away from light sources as possible.
far away from light sources as possible.
B If facing the remote control unit
B If facing the remote control unit
toward the screen to operate the
toward the screen to operate the
projector, the operating range of the
projector, the operating range of the
remote control unit will be limited by
remote control unit will be limited by
the amount of light reflection loss
the amount of light reflection loss
caused by the characteristics of the
caused by the characteristics of the
screen used.
screen used.
Connections
Notes on connections
B Read the instruction manual for each system component carefully before
connecting it.
B Turn off the power supply for all components before making any
connections.
B If the cables necessary for connecting a component to the system are not
included with the component or available as an option, you may need to
fashion a cable to suit the component concerned.
B If there is a lot of jitter in the video signal which is input from the video
source, the picture on the screen may flicker. In such cases, it will be
necessary to connect a TBC (time base corrector).
B The projector has a built-in speaker. However, you will need to connect a
separate audio system to the AUDIO OUT jack if your needs specify high
sound volumes. No sound will come out of the projector's built-in speaker
while the AUDIO OUT jack is being used.
B It may not be possible to connect some types of computer. Refer to the list
of compatible signals on page 56.
B The pin layout and signal names for the S-VIDEO IN connector are shown
below.
Pin No.
#
$
&
%
External view
B The pin layout and signal names for the RGB/YP
connector are shown below.
Pin No.
-
1
(
,
#
'
External view
Pin + is spare.
Pins &–*, , and - are for earth.
Pins . and 1 functions are only valid when
supported by the computer
Signal
#
Earth (Luminance signal)
$
Earth (Colour signal)
%
Luminance signal
&
Colour signal
P
(RGB1 IN/RGB2 IN)
B
R
Signal
#
R/P
R
$
G/G·SYNC/Y
%
B/P
B
.
SDA
/
HD/SYNC
0
VD
1
SCL
E
NGLISH
-21