Fibar Group FGS-222 Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Interruptor Fibar Group FGS-222. Fibar Group FGS-222 2 páginas. Double relay switch

Imprimir página

ENG

Technical Information

• Controlled by FIBARO system devices or any Z-Wave controller.

•

Electronic switch is a remote control unit.

• Microprocessor control.

• Active element: electromagnetic, micro-gap relay switch.

• The device may be operated by momentary and toggle

push-buttons.

•

To be installed in wall switch boxes of dimensions allowing for

installation, conforming to provisions of applicable regulations.

I General information about Fibaro system

FIBARO is a wireless system, based on Z-Wave technology.

FIBARO provides many advantages when compared to similar

systems. In general, radio systems create a direct connection

between the receiver and transmitter. But the radio signal is

OPERATING MANUAL

weakened by various obstacles located on its path (apartment

walls, furniture, etc.) and in extreme cases it fails to transfer

DOUBLE RELAY SWITCH

required data. The advantage of FIBARO system is that its devices

apart from being transmitters and receivers of signals, they are also

FGS-222-EN-A-v1.01

a signal "duplicators". When a direct connection path between the

transmitter and the receiver can not be established, the connection

may be achieved through other intermediate devices.

FIBARO is a bi-directional wireless system. It means that the signal

is not only sent to the receivers but also the receivers send the

Remotely Controlled Double Relay Switch of Fibaro System is

confirmation of its reception. This operation confirms their status so

designed to operate in a wall switch box or in locations where the

to check whether they are active. Safety of the FIBARO system

control of an electric device (up to 1.5kW) is needed.

transmission is comparable to the safety of transmission in data bus

wired systems.

It is also possible to send a signal to any system that is to be

integrated with Fibaro system.

FIBARO operates in the free band for data transmission. The

frequency depends on radio regulations in individual country . Each

Specifications

FIBARO network has its own unique network identification number

(home ID), which is why it is possible to co-operate two or more

independent systems in a single building without any interference.

Power supply:

110 - 240V ~

50 - 60Hz

Although Z-Wave is quite new technology, it has already become

recognizable and officially binding standard, similarly to Wi-Fi.

Power consumption:

to 0,8W

Many manufacturers in various industries offer solutions based on

Z-Wave technology, guaranteeing their compatibility. This means

Operational temperature:

0 - 35°C

that the system is open and it may be extended in the future. Find

more information at www.fibaro.com.

Dimensions (L x W x H):

42,50 x 38,25 x 20,30 mm

FIBARO generates a dynamic network structure. After FIBARO

For installation in boxes:

Ø ≥ 50mm

system is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

Rated load current:

6,5A per channel for resistive

signals received from devices operating in a "mesh" network.

load, but total current can not

exceed 10A*

The In-Wall Double Relay Switch is hereinafter referred to as Fibaro

Switch. It is designed to switch on/off devices connected to its

Overcurrent protection:

required external 10A circuit

terminals using radio waves, controllers and a push button directly

breaker

connected to Fibaro Switch.

Active element:

micro-gap relay switch μ

II Assembling Double Relay Switch

Device control:

remotely - radio waves

directly - push buttons

Radio protocol:

Z-Wave

Radio signal power:

1mW

Radio Frequency:

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,0 MHz RU;

865,2 MHz IN;

Range:

up to 50 m outdoors

up to 30 m indoors

(depending on building materials)

Comply with EU directives:

RoHS 2011/65/EU

LVD 2006/95/EC

EMC 2004/108/EC

R&TTE 1999/5/EC

1. Before installation ensure that the voltage supply is

disconnected.

2. Connect Double Relay Switch as shown on the diagram.

3. Place the switch in the switch box.

4. Arrange the antenna (tips are presented further).

Single switch - mains electricity power connection

Double switch - mains electricity power connection

Fig.1 Wiring diagrams for Double Relay Switch.

NOTES FOR THE DIAGRAM:

N - terminal for neutral lead

L - terminal for live lead

CAUTION

IN - input terminal for load power supply

Q1 - output terminal of the first load

Read this manual before attempting to install

Q2 - output terminal of the second load

the device! Failure to observe recommendations

S2 - terminal for key no. 2

included in this manual may be dangerous or cause

S1 - terminal for key no. 1 (has the option of entering the device in

a violation of the law. The manufacturer, Fibar

learning mode)

Group Sp. z o.o., will not be held responsible for any

B - service button (used to add or remove a device from the system)

loss or damage resulting from not following the

instructions of operating manual.

CAUTION

Product must be installed on a 10A line.

DANGER

Danger of electrocution! Electronic switch is

designed to operate in electrical home installation.

Faulty connection or use may result in fire or electric

shock.

DANGER

Danger of electrocution! All works on the device

may be performed only by a qualified and licensed

electrician. Observe national regulations.

Fig.2 Installation of Fibaro Relay Switch in wall switch box.

DANGER

Danger of electrocution! Even when the device is

CAUTION

turned off, voltage may be present at its terminals.

The switch box must be compliant with the relevant

Any

works

introducing

changes

into

the

national safety standards and it's depth should not

configuration of connections or the load must be

be less than 60mm.

always performed with disconnected voltage

(disable the fuse).

CAUTION

The device is designed for installation in wall

switch boxes and can work only with the electrical

CAUTION

connectors compliant with the relevant safety

Do not connect the device to loads exceeding

standards.

recommended

values.

Connect

only

accordance with the diagram presented in the

manual. Improper connections may be dangerous.

NOTE

Durability of the device depends on applied load.

For resistive load (light bulbs, etc.) and 6,5A current

per channel, the durability exceeds 200 000

switches.

TIPS FOR ARRANGING THE ANTENNA:

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

order to prevent interferences.

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door

frames) may impair signal reception!

Do not cut or shorten the antenna - its length is

perfectly matched to the band in which the system

operates.

NOTE

It should be noted that only the push-button

connected to S1 terminal and service push-button

S1 S2

L N

B enables "learning" mode (Include/ Exclude).

Q2 Q1 IN

SWITCH

DICTIONARY:

• Adding (Inclusion) - Z-Wave device learning mode, allowing to

add the device to existing Z-Wave network.

• Removing (Exclusion) - Z-Wave device learning mode, allowing

to remove the device from existing Z-Wave network.

• Association (linking devices) - direct control of other devices

within the Z-Wave system network.

• Multi-channel association - controlling other multi-channel

devices within the Z-Wave network.

III Activating Double Relay Switch

1. Installing the Double Relay Switch

STEP 1

S1 S2

L N

Connect the device in accordance with the wiring diagram

presented in Figure 1. Switch on the mains voltage.

Q2 Q1 IN

[Adding/Removing] Double Relay Switch [to/from] Z-wave

SWITCH

network

STEP 2

Double Relay Switch must be placed within the range of Home

Center controller, as adding mode requires direct communication

with the controller.

STEP 3

Find key no. 1 which allows to switch circuit 1 on, in accordance

with the diagram

STEP 4

Set the Home Center controller in add/remove mode (see the

controller's manual)

STEP 5

Add Double Relay Switch to the network by pushing three times key

no. 1 or push-button B located inside the housing of the device. For

toggle switch perform 3 position changes.

During the installation it is recommended to use a

momentary key connected to S1.

STEP 6

The controller indicates when the device is correctly added to the

network, (see the manual of Home Center controller).

CAUTION

Double Relay Switch cancels the "learning" mode

after key no. 1 is pressed once. Therefore, pressing

key no. 1 four times will not add the devices to the

network. The same applies to push-button B.

CAUTION

Double Relay Switch is set by default to operate

with momentary switches (i.e. single-pole switch or

bell switch). While adding Double Relay Switch to

the network with toggle switches, ensure that all

switch contacts are open (off), because closing

them results in activating the push-button and this

will prevent adding the device to the network.

2. Resetting Double Relay Switch

Fibaro Switch provides two methods for resetting.

Method I : Reset by removing Double Relay Switch from the

existing Z-Wave network. The device may be removed using the

controller that has the ability to include/exclude devices from/to

Z-Wave network (see the manual of controller).

Method II : Reset by holding B button for 3 sec. after connecting

mains voltage to the Switch

3. Controlling Double Relay Switch by momentary or

V Configuration

toggle switches.

The following settings are available in the Fibaro interface as

Momentary switch (after releasing the push-button a spring

simple options that may be chosen by selecting the appropria-

automatically pushes back and disconnects the button)

box.

- Turning on/off circuit 1 or 2 - briefly press the push-button

In order to configure Fibaro Switch (using the Home Center

corresponding to a chosen circuit (see diagram).

controller), go to device options by clicking the following icon:

Toggle switch (operates as a two-position switch, it has no

Select „Advanced" tab.

spring that would push back the device after releasing manual

pressure)

Parameter No. 1 - Activate / deactivate functions ALL ON / ALL

- Turning on/off the circuit - change the position of selected

OFF.

push-button from the current position.

Default value: 255

Options for changing parameter 255, 0, 1, 2

4. Controlling Double Relay Switch using a

command: ALL ON / ALL OFF

Available configuration parameters:

255 - ALL ON active, ALL OFF active.

0 - ALL ON is not active ALL OFF is not active

Fibaro Switch responds to commands ALL ON / ALL OFF that may

1 - ALL ON is not active ALL OFF active

be sent by the controller. ALL ON / ALL OFF commands are usually

2 - ALL ON active ALL OFF is not active

implemented in Z-Wave remote control.

Parameter No. 3 - Auto off relay after specified time, with the

By default, Fibaro Switch accepts both active commands ALL ON

possibility of manual override - immediate Off after button

and ALL OFF. Settings may be changed by entering an appropriate

push.

value into configuration register no. 1 (see configuration)

Default value: 0

Available settings:

5. Controlling Double Relay Switch using Home

0 - manual override disabled. After single button push the relay turns

Center controller

on and automatically turns off after specified time.

1 - manual override enabled. After single button push the relay turns

After adding Double Fibaro Switch to the network, it will be

on and automatically turns off after specified time. Another button

represented in Home Center by the following two icons (one icon

push turns the relay off immediately.

represents one channel):

Parameter No. 4 - Auto off for relay 1.

Default value: 0

Available settings:

[1 - 65535] (0,1 s – 6553,5 s) Time period for auto off, in miliseconds

0 - Auto off disabled

Parameter No. 5 - Auto off for relay 2.

Default value: 0

Fig.3 Icons of Double Relay Switch shown by

Available settings::

Home Center controller

[1 - 65535] (0,1 s – 6553,5 s) Time period for auto off, in miliseconds

0 - Auto off disabled

Turning on/off the device connected to Double Relay Switch is

performed by pressing ON/OFF icon.

Parameter No. 6 - Sending commands to control devices

assigned to 1-st association group (key no. 1).

IV Association

Default value: 0

Available configuration parameters:

Association enables Fibaro Switch to directly control a device

included in Z-Wave network e.g. Dimmer, Switch (ON-OFF), Roller

0 - commands are sent when device is turned on and off

Shutter or scene (scene may be controlled only through the Home

Center controller).

1 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command, dimmers memorize the last saved state (e.g. 50%

brightness).

Association ensures direct transfer of control

commands between devices, and is performed

2 - commands are sent when device is turned off. Enabling device

without participation of the main controller.

does not send control commands. Double-clicking key sends 'turn

on' command and dimmers are set to 100% brightness.

Fibaro Switch provides association of three groups.

NOTE: Parameter 15 value must be set to 1 to work properly.

This activates the double-click functionality - dimmer/roller

1st group is assigned to key no. 1

shutter control.

2nd group is assigned to key no. 2

Parameter No. 7 – Sending commands to control

assigned to 2-nd association group (key no. 2).

3rd group reports state of devices. Only one device can be

associated to this group.

Default value: 0

Fibaro Switch enables user to control up to 5 normal devices, and

Available configuration parameters:

5 MultiChannel devices in group no. 1 and no. 2, group no. 3 has

only one field. One field is reserved for the network controller.

0 - commands are sent when device is turned on and off

1 - commands are sent when device is turned off. Enabling device

To add an association (using the Home Center controller), go to

does not send control commands. Double-clicking key sends 'turn

on' command, dimmers memorize the last saved state (e.g. 50%)

device options by clicking the following icon:

2 - commands are sent when device is turned off. Enabling device

Select the "device options" tab. Then specify to which group and

does not send control commands. Double-clicking key sends 'turn

what devices are to be associated. Sending relevant information to

on' command and dimmers are set to 100% brightness.

devices added to associated groups may take even a few minutes.

Info: Parameter 15 must be set to 1 to make this parameter work

properly. This activates the double-click functionality - dimmer/roller

shutter control.

WARNING

When Fibaro Switch sends control commands and

a new command is issued, then the current one

Parameter No. 13 - Assigns bistable key status to the device

command transmission is interrupted to send new

status.

commands.

Default value: 0

FGS-222 Fibaro Switch supports the operation of multi-channel

Available configuration parameters:

devices. Multichannel devices are devices that include two or more

0 - [On / Off] device changes status on key status change.

circuits inside one physical unit.

1 - Device status depends on key status: ON when the key is ON,

OFF when the key is OFF.

FGS-222 Double Relay Switch is a multichannel device. It means

that it has two independent executive circuits - each circuit is

recognized by the Home Center controller as a separate device.

Accordingly, each channel is represented by an independent icon.

The first channel is operated by a push-button connected to S1

terminal and it is the main (default) channel.

The association of the second channel of the double relay

switch may be operated only by devices supporting

multi-channel association !

devices

Remote control from Fibaro System is still

possible. This function is useful when you want

display status of external devices, e.g. Motion

Sensor, in Fibaro System.