Shimano FC-R9100-P Manual del usuario - Página 2

Navegue en línea o descargue pdf Manual del usuario para Accesorios para bicicletas Shimano FC-R9100-P. Shimano FC-R9100-P 2 páginas.

Imprimir página

Names of parts

Control unit

Gears

LED

Button

Charging port

Fastening section

Outer cap

Sensor

Crank arm

ANT ID

Magnet

Left crank

Connection

Connector

terminal

Electric wire

Operation

You cannot use the battery immediately after shipment.

Be sure to charge it before use.

Charging the battery

This product can be charged by using an AC adapter with a USB port or by

connecting it to the USB connector of a PC.

Power may no longer be supplied to the battery if the PC enters a

hibernation or sleep state while charging.

1. Pull at the indent in the control unit to open the cover.

Push upward

Indent

2. Connect the charging cable as shown in the illustration. (Match the

shapes of the charging cable and charging port when connecting.)

3. Once charging begins, the LED lights up blue.

(Do not move the crank or cable during charging. There is a risk of the cable

disconnecting. Reconnect the cable if it disconnects.)

LED

(lights up blue)

4. Once charging is complete, the LED turns off.

After charging, make sure to close the cover.

How to check battery level

1. Press the button on the control unit.

2. The LED is green or red.

If the LED is red, ﬂ ashing, or does not turn ON, the battery level is low.

Charge the battery.

LED

Battery level

Green

100% - 16%

Red

15% - 3%

LED

Red

(lights up

2% - 1%

green or red)

(ﬂ ashing)

Off

Note:

When the LED is lit up red, you will not be able to connect to E-TUBE

PROJECT.

If you continue usage in this state and the LED ﬂ ashes red, you will be

unable to set zero offset.

Activating the product

Press the button on the control unit or rotate the crank 2 or more times.

Conﬁ rming the product has activated

• Activation by pressing the button

Remaining battery charge displays.

• Activation by rotating the crank (after connecting cycle computer)

Cadence and power display on the cycle computer when the product is

active.

If this product does not detect motion for 5 minutes after activation,

wireless transmission will terminate in order to save battery power.

To re-enable the wireless connection, either press the button on the

control unit or rotate the crank 2 or more times.

Connection procedure

Cycle computer connection

To make a connection, the cycle computer needs to be in connection mode.

For information on how to put the cycle computer into connection mode,

refer to the manual for the cycle computer.

1. Activate the product by pressing the button on the control unit or

rotating the crank 2 or more times.

2. Select the unit name displayed on the cycle computer screen.

For an ANT

connection, you can also connect by entering the ﬁ ve

+ TM

digit ANT ID found on the reverse side of the right crank.

ANT ID

3. This completes the connection process.

Check on the cycle computer to see if connection was successful.

If a connection cannot be made in the way described above, refer to the

manual for your cycle computer.

E-TUBE PROJECT connection

Before setting up a connection, turn on Bluetooth LE on the smartphone/

tablet.

1. Open E-TUBE PROJECT and set it to listen for Bluetooth LE signals.

2. Press the button on the control unit.

3. Select the unit name displayed on screen.

* To disconnect, cancel the Bluetooth LE connection from the smartphone/

tablet. (The cycle computer will exit connection mode and return to

regular operation mode.)

To restore the Bluetooth LE Name and Passkey to their default values,

hold down the button on the control unit for at least 3 seconds during

battery charging. The LED will ﬂ ash blue.

(Bluetooth LE Name: FCR9100P Passkey: 000000)

Performing zero offset calibration

• Zero offset calibration can be performed using the control unit or the cycle

computer.

When calibrating using the cycle computer, refer to the instruction manual

for the cycle computer.

• It is recommended to perform zero offset calibration before riding the

bicycle.

1. Place the bicycle on level ground.

(At this time, do not place your feet on the pedals or apply load to the

crank. It may not be possible to perform calibration correctly.)

2. Position the crank arm so that it is perpendicular to the ground as in the

illustration.

(Zero offset calibration is unaffected by whether the chain is positioned

on the largest chainring or smallest chainring.)

3. Press the button on the control unit until the LED lights up blue.

LED

(lights up blue)

Button

4. When the LED lights up blue, release the button.

The LED will begin blinking and zero offset calibration will complete.

LED

(blinks blue)

When connected to a cycle computer via ANT

or connected to E-TUBE

+ TM

PROJECT, "5050" will be displayed on your cycle computer, smartphone,

or tablet once zero offset conﬁ guration is complete.

If some other number is displayed even if you perform zero offset

conﬁ guration again, contact the place of purchase or a bicycle dealer.

Speciﬁ cations

Operating

Continuous

300 or more hours

temperature

-10°C – 50°C

operation

(for given

range

time

temperature of 25°C)

Battery type

Lithium ion

Normal

2.5 hours

charging time

Wireless

ANT

/Bluetooth

Charging

speciﬁ cation

0°C – 45°C

temperature

Frequency band

2,402 – 2,480 MHz

Maximum radio-frequency power

+4 dBm

Firmware version

4.0.3 –

Troubleshooting

If you experience any trouble using this product, please refer to the

following.

If none of the following are applicable, or the suggested solution does not

resolve the issue, consult with the place of purchase or a bicycle dealer.

If the power value has changed, it is possible to correct it. For details, consult

the place of purchase.

The cycle computer may not be connected.

Follow the steps in "Connection procedure" to make a

connection.

The battery may be out of charge.

Power does not

Check remaining battery charge and charge the battery

display

if the charge is low.

The left crank connector may be detached.

Remove the outer cap and check that the connector is

connected.

Zero offset calibration may not be correct.

Power value is

Perform zero offset calibration referring to the section

abnormal

"Performing zero offset calibration".

The magnet may not be attached or may be positioned

Cadence does not

incorrectly.

display

If it is not attached or it is positioned incorrectly,

consult with the place of purchase or a bicycle dealer.

Cadence value is

Another cadence sensor may be attached.

abnormal

If this is the case, either remove or disable it.

There may have been an issue during zero offset

LED blinks red

calibration.

during zero offset

Conﬁ rm that the connector is connected and perform

calibration

zero offset calibration again referring to the section

"Performing zero offset calibration".

A USB hub may be connected.

Do not use a USB hub.

Charging is not

possible

The charging cable may be damaged.

If charging is not possible even after trying a different

PC or USB adapter, replace the charging cable.

The cycle computer in use may not be supported.

Conﬁ rm with the instruction manual for the cycle

computer.

Interference may be affecting the wireless signals.

Wireless signals may be susceptible to interference in

the following locations and conditions, preventing

Connection cannot

successful connection.

be made with cycle

* Near televisions, PCs, radios, motors/engines etc., or

computer

inside cars and trains.

* Near railroad crossings, railway tracks, television

transmitting stations or radar bases, etc.

* When used alongside other wireless/cordless devices

or certain types of lighting.

Change location and reattempt connection.

About hardware reset

If an issue cannot be resolved even after referring to the troubleshooting

section, perform a hardware reset.

1. Hold down the button on the control unit for 15 seconds.

2. The hardware reset completes when the button is released.

3. When the hardware reset is complete, the LED will light up indicating

remaining battery charge.

After the hardware reset is complete, check operation again and if the

issue has not been resolved, consult with the place of purchase or a

bicycle dealer.

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222

Please note: speciﬁ cations are subject to change for improvement without notice. (English)