Sony XPlod MEX-BT5000 Manual de instrucciones - Página 25
Navegue en línea o descargue pdf Manual de instrucciones para Sistema estéreo Sony XPlod MEX-BT5000. Sony XPlod MEX-BT5000 28 páginas. Cd player xplod bluetooth
También para Sony XPlod MEX-BT5000: Instalación/Conexiones (2 páginas), Manual de instrucciones y funcionamiento (2 páginas), Manual rápido (2 páginas), Instrucciones de uso (2 páginas), Especificaciones (2 páginas), Instalación/Conexiones (2 páginas), (Portugués) Especificaciones (1 páginas)
Imprimir página
E:\Working\2693038211\269303821MEXBT5000U\01US02CD-U.fm
E:\Working\2693038211\269303821MEXBT5000U\01US02CD-U.fm
01US+00COV-U.book Page 25 Thursday, April 27, 2006 11:03 PM
Automatic tuning is not possible.
• The local seek mode is set to "on."
t Set to "Local off" (page 17).
• The broadcast signal is too weak.
t Perform manual tuning.
During FM reception, the "ST" indication
flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
t Set to "Mono on" (page 17).
An FM program broadcast in stereo is heard in
monaural.
The unit is in monaural reception mode.
t Set to "Mono off" (page 17).
Bluetooth function
The connecting device cannot detect this unit.
• Set "Signal" to "ON" (page 12).
• Set "Visibility" to "Show" (page 12).
• While connecting to the other Bluetooth device, this
unit cannot be detected from another device.
Disconnect the current connection and search for this
unit from another device. The disconnected device
can be reconnected by selecting from the list of
registered devices.
This unit cannot detect the connecting device.
Check the Bluetooth setting of the connecting device.
Connection is not possible.
• Depending on the other device, searching from this
unit may not be possible.
t Search for this unit from the other device.
• Depending on the status of the other device,
searching from this unit may not be possible.
t Search for this unit from the other device.
• Check the pairing procedures referring to the manual
of the other device, etc., and perform the operation
again.
The name of the detected device does not
appear.
Depending on the status of the other device, it may not
be possible to obtain the name.
No ring tone.
• Adjust the volume in "Ring Vol" (page 14).
• Depending on the connecting device, the ring tone
may not be sent properly.
t Set "Ringtone" to "Default" (page 15).
The talker's voice volume is low.
Adjust the volume in "Talk Vol" (page 14).
Echo or noise occurs in phone call
conversations.
• Lower the volume.
• "EC/NC Mode" is set to "off."
t Set "EC/NC Mode" to "Mode 1" or "Mode 2"
(page 15).
• If the ambient noise other than the phone call sound
is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is loud,
shut the window. If the air conditioner is loud, lower
the air conditioner.
The phone sound quality is poor.
Phone sound quality depends on reception conditions
of cellular phone.
t Move your car to a place where you can enhance
the cellular phone's signal if the reception is poor.
The sound skips during playback of a
Bluetooth audio device.
• Reduce the distance between the unit and the
Bluetooth audio device.
• If the Bluetooth audio device is stored in a case
which interrupts the signal, remove the audio device
from the case while using.
• Several Bluetooth devices or other devices which
emit radio waves are used nearby.
t Turn off the other devices.
t Reduce the distance from the other devices.
The connected Bluetooth audio device cannot
be controlled.
Check that the connected Bluetooth audio device
supports AVRCP.
Some functions do not work.
Check that the connecting device supports the
functions in question.
The name of the other party does not appear
when a call is received.
• The other party is not stored in the phonebook.
t Store in the phonebook (page 14).
• The calling phone is not set to send the phone
number.
A call starts unintentionally.
• The connecting phone is set to start a call
automatically.
• "Auto Answer" of this unit is set to "on" (page 15).
Pairing failed in Time Over.
Depending on the connecting device, the time limit for
pairing may be short. Try completing the pairing
within the time by setting a single digit passcode.
The ring tone or other party's voice is output
only from one speaker.
"Speaker Sel" is set to "FR-L" or "FR-R."
t Set "Speaker Sel" to "Front" (page 16).
continue to next page t
2-693-038-21 (1)
masterpage:Right
masterpage:Right
25
MEX-BT5000