Digitrax UT1 Manual - Página 6

Navegue en línea o descargue pdf Manual para Unidad de control Digitrax UT1. Digitrax UT1 11 páginas. Traditional style loconet throttle

Imprimir página

3.10 F1/F4/ON Key

Press F1 to toggle Function 1 on and off.

Hold "Shift" and press F4 to toggle Function 4 on and off.

Press "RUN/STOP" and "ON" together to turn track power on.

3.11 F2/F5/OFF Key

Press F2 to toggle Function 2 on and off.

Hold "Shift" and press F5 to toggle Function 5 on and off.

Press "RUN/STOP" and "OFF" together to turn track power off.

3.12 Four Top Row LEDs (Chase Lights)

Indicates function status, lit when on

All four LEDs strobing left to right means that you need to increase

speed on the throttle knob to complete the selection of a locomotive.

All four LEDs strobing right to left means that you need to decrease

speed on the throttle knob to complete the selection of a locomotive.

Indicates CLOSED when in Switch Mode.

LED above ACQ blinking every 4 seconds indicates that the throttle

is active.

4.0 UT1: System Modes

4.1 UT1 Configuration Mode

The UT1 comes from the factory configured with the most common fea-

tures enabled as defaults. You can change these features to suit your

particular needs by the following procedure.

4.1.1 UT1 Configuration Options

1. Choose the features you want from the chart below. Add up the val-

ues of your choices to get the "SETTING" value. Example: 0 (Safe

Mode) + 2 (F2 Toggle on/off) + 0 (F3 toggle on/off) = "SETTING"

of 2.

TABLE I

Defaults

0=Safe Mode

0=F2 Momentary

operation

0=F3 Toggles

on/off

2. With the UT1 unplugged from LocoNet, Set the rotary selectors to

the proper setting (See Table I).

3. Press and hold the F0 key while you plug the UT1 into the LocoNet

Options

1=Quik Mode

2=F2 Toggles on/off

4=F3 Momentary

operation

network. As soon as the UT1 powers up, release the F0 key. The

UT1 is now set to the new configuration and will continue to use

this configuration until you change it again. The UT1 will remember

this new configuration whether it is plugged in or not.

4.1.2 UT1 ID Number

All UT1 throttles come from the factory with the Throttle ID set to "00".

As you add throttles it is a good idea to make each throttle's ID

unique. Use the following procedure to set the ID number.

1. Unplug the UT1 from LocoNet.

2. Set the two digit ID number of your choice on the two rotary selec-

tors.

3. Press and hold the "SHIFT/PROG" key and plug back into LocoNet.

4. Release the "SHIFT/PROG" key. The UT1 will remember this num-

ber until you decide to change it.

4.2 Track Power Mode

If track power is off, press "RUN/STOP" and "ON" simultaneously to

have the Digitrax command station turn on the track power & go

through power up sequencing. Press "RUN/STOP" and "OFF" to

turn track power off.

4.3 Walkaround Operation on LocoNet

The UT1 does not use a battery to maintain its internal memory. All data

is stored in EEPROM. When the UT1 is connected to LocoNet It

receives its total power requirements from the network.

NOTE: The UT1 draws approximately 15 mA at a minimum 6.8V

DC and gets its total power requirements from the network. It

may be necessary to supplement the network power supply, on

large networks, when using multiple throttles. This can be done

using Digitrax UP5 Universal Panel(s), to expand LocoNet, with

the battery saver option hooked up.

When a UT1 is disconnected from the network it turns off, but all the

settings are retained in EEPROM while you move to a different part

of the layout.. When the UT1 is re-connected to the network, it will

reselect the locomotive it was previously controlling with all the pre-

vious settings intact.

When a UT1 with a selected in-use locomotive is disconnected from

LocoNet, for more than the system purge time (about 200 seconds),

the Command Station will purge these in-use locomotives to the

common state so that other throttles can access these locomotives. If