Epson PowerLite 1825 Manual del usuario - Página 10

Navegue en línea o descargue pdf Manual del usuario para Software Epson PowerLite 1825. Epson PowerLite 1825 14 páginas. Release of check tool for network projectors v1.00 for windows
También para Epson PowerLite 1825: Manual del usuario (42 páginas), Manual de instrucciones (36 páginas), Configuración rápida (2 páginas), Manual de instrucciones (47 páginas), Declaración de conformidad (4 páginas), Especificación del producto (2 páginas), Lista de piezas (1 páginas), Boletín de asistencia sobre productos (25 páginas), Boletín de asistencia sobre productos (38 páginas), Boletín de asistencia sobre productos (12 páginas), Boletín de asistencia sobre productos (42 páginas), Boletín de asistencia sobre productos (22 páginas), Boletín de asistencia sobre productos (28 páginas), Boletín de asistencia sobre productos (41 páginas), Boletín de asistencia sobre productos (34 páginas), Boletín de asistencia sobre productos (38 páginas), Boletín de asistencia sobre productos (28 páginas), Boletín de asistencia sobre productos (15 páginas), Boletín de asistencia sobre productos (22 páginas)

Epson PowerLite 1825 Manual del usuario
PowerLite 1825
Hold down the
button on the remote control and use the
Num
numeric keypad to enter the four-digit password. The password
screen closes and projection begins.
If the password is not correct, you see a message prompting you
to re-enter it. If you enter an incorrect password three times in
succession, you see the message
and the projector switches to standby mode.
be locked
Disconnect the projector's power cord from the electrical outlet,
reconnect it, and turn the projector back on.
When you see the Password screen again, you can try to enter
the correct password.
If you enter an incorrect password 30 times in succession, the
projector remains locked and you must contact Epson to unlock
it. If you have forgotten the password, contact Epson with the
request code number that appears in the Password screen for
assistance.
Note: If you leave the projector plugged in, the Password Protect
Release screen will not appear. It appears only if you unplug and
reconnect the power cable.

Disabling the Projector's Buttons

When you enable the Operation Lock function, you can lock all
the projector's buttons, or all buttons except the P
button. The remote control can still be used to operate the
projector.
1. Press the
button, highlight the
Menu
press
.
Enter
2. Select
Operation Lock
3. Select
(to lock all projector buttons) or
Full Lock
(to lock all buttons except the
Lock
press
.
Enter
4. Select
and press
Yes
Enter
5. Press the
button to exit.
Menu
To disable the Operation Lock function, select
Operation Lock menu. Or press and hold the
the projector's control panel for 7 seconds. A message is
displayed and the lock is released.
10
Hold down
The projector's operation will
Power
menu, and
Settings
and press
.
Enter
Partial
button) and
Power
to confirm the setting.
in the
Off
button on
Enter

Checking Projector Status

If your projector isn't working correctly, first turn it off, wait for
it to cool (the
Power
Then plug the power cord back in and turn on the projector. If
this doesn't solve the problem, check the lights on top of the
projector.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector's status.
Power light
Lamp light
The following table describes the projector's status lights.
Status lights
Light
Status
Orange
Flashing
green
Green
Flashing
orange
Red
Flashing
orange
2/08
light stops flashing orange), and unplug it.
Temperature light
Description
The projector is in sleep or standby mode.
You can unplug it or press the
button to turn it on.
The projector is warming up. Wait for the
image to appear.
The projector is operating normally.
The projector is cooling down. You can't
turn it back on until the light stops flashing
and remains orange.
There is a problem with the projector.
Check the other two lights and the
information on this page to diagnose the
problem.
Rapid cooling is in progress. Although this
is not an abnormal condition, projection
will stop automatically if the temperature
rises higher. Make sure there is plenty of
space around and under the projector for
ventilation, and that the air filters and
vents are clear.
Power
P