Pioneer Super Tuner IIID AVH-P3100DVD Manual de instalación - Página 2
Navegue en línea o descargue pdf Manual de instalación para Receptor para automóvil Pioneer Super Tuner IIID AVH-P3100DVD. Pioneer Super Tuner IIID AVH-P3100DVD 8 páginas. Dvd rds av receiver
También para Pioneer Super Tuner IIID AVH-P3100DVD: Manual de instalación (38 páginas), Manual de instalación (43 páginas), Folleto (9 páginas), Manual de inicio rápido (8 páginas)
Imprimir página
Connecting the units
Connecting the power cord
Note:
This product
Depending on the kind of vehicle, the
function of 3* and 5* may be different. In
this case, be sure to connect 2* to 5* and
4* to 3*.
1*
3*
2*
Antenna input
Fuse (10 A)
5*
4*
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if this
terminal is not in use.
Yellow (3*)
Yellow (2*)
Back-up
Connect to the constant 12 V
(or accessory)
supply terminal.
Fuse resistor
Red (5*)
Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
Orange/white
Fuse resistor
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
Speaker leads
ISO connector
Note:
White:
Front left
In some vehicles, the ISO connector may be
White/black: Front left
Gray:
Front right
divided into two. In this case, be sure to connect
Gray/black:
Front right
to both connectors.
Green:
Rear left
or subwoofer
Green/black: Rear left
or subwoofer
When you connect the separately sold
Violet:
Rear right
or subwoofer
multi-channel processor (DEQ-P6600) to this
Violet/black:
Rear right
or subwoofer
unit, do not connect anything to the speaker
leads and system remote control (blue/white).
Connecting the units
Fuse resistor
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
Yellow/black
If you use equipment with Mute function, wire this lead to the
Audio Mute lead on that piece of equipment. If not, keep the
Audio Mute lead free of any connections.
Connection method
2. Clamp firmly with
1. Clamp the lead.
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Parking brake
Connect to system control terminal of the power
switch
Power supply side
amp (max. 300 mA 12 V DC).
Ground side
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
Notes:
connector will differ depending on
the type of vehicle. Connect 6* and
· Change the initial setting of this unit (refer to the Operation Manual).
7* when Pin 5 is an antenna control
The subwoofer output of this unit is monaural.
type. In other types of vehicles,
· When using a subwoofer of 70 W (2 Ω) , be sure to connect with
never connect 6* and 7*.
Violet and Violet/black leads of this unit. Do not connect anything to
Green and Green/black leads.
Connecting the units
When connecting to separately sold power amp
Rear output or
subwoofer output
Power amp
Front output
(sold separately)
To rear output or
subwoofer output
Power amp
(sold separately)
To front output
This product
Connect with RCA cables (sold
separately)
Blue/white
Connect to system control
terminal of the power amp
(max. 300 mA 12 V DC).
System remote control
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna
relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 6*
Left
Right
and 7* when Pin 5 is an antenna control type.
In other types of vehicles, never connect 6* and
7*.
When you connect the separately sold
Front speaker
Front speaker
multi-channel processor (DEQ-P6600) to this
unit, do not connect anything to the speaker
leads and system remote control (blue/white).
Rear speaker
Rear speaker
When you connect the multi-channel processor
or Subwoofer
or Subwoofer
to this unit, refer to multi-channel processor's
installation manual for the connection method.
Note:
Perform these connections when
using the optional amplifier.
· Change the initial setting of this unit
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.
Connecting the units
Connecting the system
Wired remote input
Microphone
for hands-free phoning
Hard-wired remote control
(supplied with Bluetooth adapter)
adaptor can be connected
(sold separately).
Bluetooth adapter
(e.g. CD-BTB200)
(sold separately)
Blue
IP-BUS input
(Blue)
Black
This product
IP-BUS cable
(Supplied with Bluetooth adapter)