Pioneer Super Tuner IIID AVH-P3100DVD 설치 매뉴얼 - 페이지 2

{카테고리_이름} Pioneer Super Tuner IIID AVH-P3100DVD에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer Super Tuner IIID AVH-P3100DVD 8 페이지. Dvd rds av receiver
Pioneer Super Tuner IIID AVH-P3100DVD에 대해서도 마찬가지입니다: 설치 매뉴얼 (38 페이지), 설치 매뉴얼 (43 페이지), 브로셔 (9 페이지), 빠른 시작 매뉴얼 (8 페이지)

페이지 인쇄

Pioneer Super Tuner IIID AVH-P3100DVD 설치 매뉴얼

Connecting the units

Connecting the power cord

Note:

This product

Depending on the kind of vehicle, the

function of 3* and 5* may be different. In

this case, be sure to connect 2* to 5* and

4* to 3*.

Antenna input

Fuse (10 A)

Connect leads of the same

color to each other.

Cap (1*)

Do not remove cap if this

terminal is not in use.

Yellow (3*)

Yellow (2*)

Back-up

Connect to the constant 12 V

(or accessory)

supply terminal.

Fuse resistor

Red (5*)

Red (4*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

Orange/white

Fuse resistor

Connect to lighting switch terminal.

Black (chassis ground)

Connect to a clean, paint-free metal location.

Speaker leads

ISO connector

Note:

White:

Front left

In some vehicles, the ISO connector may be

White/black: Front left

Gray:

Front right

divided into two. In this case, be sure to connect

Gray/black:

Front right

to both connectors.

Green:

Rear left

or subwoofer

Green/black: Rear left

or subwoofer

When you connect the separately sold

Violet:

Rear right

or subwoofer

multi-channel processor (DEQ-P6600) to this

Violet/black:

Rear right

or subwoofer

unit, do not connect anything to the speaker

leads and system remote control (blue/white).

Connecting the units

Fuse resistor

Violet/white

Of the two lead wires connected to the back lamp, connect the one

in which the voltage changes when the gear shift is in the

REVERSE (R) position. This connection enables the unit to

sense whether the car is moving forwards or backwards.

Yellow/black

If you use equipment with Mute function, wire this lead to the

Audio Mute lead on that piece of equipment. If not, keep the

Audio Mute lead free of any connections.

Connection method

2. Clamp firmly with

1. Clamp the lead.

needle-nosed pliers.

Note:

· The position of the parking brake switch depends on the vehicle model. For details,

consult the vehicle Owner's Manual or dealer.

Light green

Used to detect the ON/OFF status of the parking brake. This lead

must be connected to the power supply side of the parking brake

switch.

Blue/white

Parking brake

Connect to system control terminal of the power

switch

Power supply side

amp (max. 300 mA 12 V DC).

Ground side

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO

Notes:

connector will differ depending on

the type of vehicle. Connect 6* and

· Change the initial setting of this unit (refer to the Operation Manual).

7* when Pin 5 is an antenna control

The subwoofer output of this unit is monaural.

type. In other types of vehicles,

· When using a subwoofer of 70 W (2 Ω) , be sure to connect with

never connect 6* and 7*.

Violet and Violet/black leads of this unit. Do not connect anything to

Green and Green/black leads.

Connecting the units

When connecting to separately sold power amp

Rear output or

subwoofer output

Power amp

Front output

(sold separately)

To rear output or

subwoofer output

Power amp

(sold separately)

To front output

This product

Connect with RCA cables (sold

separately)

Blue/white

Connect to system control

terminal of the power amp

(max. 300 mA 12 V DC).

System remote control

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna

relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 6*

Left

Right

and 7* when Pin 5 is an antenna control type.

In other types of vehicles, never connect 6* and

7*.

When you connect the separately sold

Front speaker

multi-channel processor (DEQ-P6600) to this

unit, do not connect anything to the speaker

leads and system remote control (blue/white).

Rear speaker

When you connect the multi-channel processor

or Subwoofer

to this unit, refer to multi-channel processor's

installation manual for the connection method.

Note:

Perform these connections when

using the optional amplifier.

· Change the initial setting of this unit

(refer to the Operation Manual).

The subwoofer output of this unit is monaural.

Connecting the units

Connecting the system

Wired remote input

Microphone

for hands-free phoning

Hard-wired remote control

(supplied with Bluetooth adapter)

adaptor can be connected

(sold separately).

Bluetooth adapter

(e.g. CD-BTB200)

(sold separately)

Blue

IP-BUS input

(Blue)

Black

This product

IP-BUS cable

(Supplied with Bluetooth adapter)