Ariston WMTF 703 H HK Manual de instrucciones e instalación - Página 15

Navegue en línea o descargue pdf Manual de instrucciones e instalación para Lavadora Ariston WMTF 703 H HK. Ariston WMTF 703 H HK 16 páginas. Top loading washer

Imprimir página

Ariston WMTF 703 H HK Manual de instrucciones e instalación

檢測功能及故障指示說明 Description of failure indicators

檢測功能及故障指示說明

Failure indicator

Indication on display

lights up

(if available)

(in case your washing

machine has no display:

of the programme

技術支援

Service

水喉已關

Water tap closed

清理水泵

Clean pump

Possible causes / Solutions

洗衣程序期間停止操作。內桶機門打開，即內桶機門並未正常關上。

Appliance stops during the programme. Drum flaps open (the drum flaps have not been closed

bdd

properly).

按下重置按鈕約

選合適程序繼續操作。如情況持續，聯絡維修服務部。

all lamps

Push the Reset button for at least 3 seconds and wait until the Door open

and close drum flaps, then select and start desired programme again. If fault persists, notify our

flow bar light up)

After-Sales Service.

電子組件故障

啟動排水程序及按下重設按鈕約

from F02 to F35

Electrical module fault

(except F09)

Select and start Drain programme or push Reset button for at least 3 seconds.

水位過高

關閉洗衣機，並再次啟動，選取排水程序後

Water level too high (after programme cancellation or false operating)

F09

Switch off appliance and then switch it on again, select programme Drain and start within 15

seconds.

不停注水故障

關閉洗衣機，拔除電源插頭及關閉水源。小心地將洗衣機傾側，讓機底部多餘水量流出。

Switch off appliance, pull out mains plug and turn water tap off. Tilt appliance forward carefully to

allow collected water to flow out from the bottom. Then:

再次連接電源。

Plug in the appliance again.

開啟水源。此時洗衣機仍未啟動，如水源直接注入洗衣機內，表示故障仍存在；關閉水源，並聯絡

維修服務部。

Turn the water tap on (if water immediately flows into the appliance without the appliance being

started, there is a failure; turn off the tap and notify After-Sales Service).

過量泡沫

太多泡沫而導致洗衣程序未能正常操作。

Too much foam interrupted the wash programme.

啟動過水程序。

Select and start Rinse & Spin programme.

Fod

再重選洗衣程序，祇用少量洗滌劑。

Afterwards select and start desired programme again, using less detergent.

如情況仍持續，關閉水源，並聯絡維修服務部。

If faults persist, unplug the appliance, turn off the water tap and contact our After-Sales Service.

已按下開始

Appliance has no or insufficient water supply. The Start/Pause light blinks. Check whether:

水源已開啟，但水壓不足。

Water tap is fully open and water supply pressure is sufficient.

進水軟喉管扭曲。

Kinks are present in water inlet hose.

進水過濾網被堵塞

Mesh filter of water supply hose is blocked (see p11 Care and maintenance).

問題解決後，按開始

After problem has been removed, restart programme by presenting Start/Pause. If the fault occurs

again, contact our After-Sales Service.

洗衣後污水未能排出。洗衣機停止該階段操作。先拔除電源及檢查本機︰

Waste water is not pumped out. The appliance stops in the corresponding programme step; unplug

it and check whether:

排水軟喉管扭曲。

Kinks are present in the drain hose.

過濾網或水泵被堵塞

才可排出

Filter or pump is blocked (see p12 Cleaning the Filter/Draining residual Water; make sure the

water has cooled before draining the appliance).

問題解決後，開啟排水程序或按重設按鈕至少

部。

After problem has been removed, select and start Drain programme or push Reset button for at least

3 seconds; afterwards restart desired programme. If the fault occurs again, contact our After-Sales

Service.

秒直至機門可打開指示燈亮起。打開洗衣機門後，再將內桶機門關上，再次揀

秒。

(

於已取消洗衣程序或操作不當

Waterstop fault

Overfoaming

暫停掣，但洗衣機仍進水量不足。可能是︰

(

可參閱第

頁保養須知

暫停掣重啟程序。如情況仍持續，聯絡維修服務部。

(

可參閱第

頁過濾網清理

)

。

)

秒內再次啟動。

)

。

剩餘水量排出；如有須要，緊記待機內熱水冷卻後

秒，再重選洗衣程序。如情況仍持續，聯絡客戶服務

lights up. Open lid