djm direct DJMSL12 Manual de instrucciones - Página 6
Navegue en línea o descargue pdf Manual de instrucciones para Sierra djm direct DJMSL12. djm direct DJMSL12 15 páginas. 12 double bevel compound sliding mitre saw
Imprimir página
· Do not slow or stop a blade with a piece of wood. Let the blade
come to rest naturally.
· If you are interrupted when operating the saw, complete the
process and switch off before looking up.
· Periodically check that all nuts, bolts and other fixings are properly
tightened.
· Do not store materials or equipment above a machine in such a
way that they could fall into it.
· Always hold the saw on parts that are insulated. If you accidentally
cut into hidden wiring or the saw's own cable, the metal parts of the
saw will become "live". Switch off at the mains and remove the plug
immediately.
· Never saw near combustible liquids or gases. · Note the direction
of rotation of the motor and the blade.
· Do not lock the movable guard in the open position and always
ensure that it is working properly, freely rotating and returning to
fully cover the teeth of the blade.
· Connect the saw to a dust collection devise and ensure that it is
operated properly. As the operator of the saw, please make sure that
you understand factors that influence exposure to dust, including the
type of material to be machined, the importance of local extraction
and the proper adjustment of hoods/baffles/ shoots of your dust
extraction system. We recommend that you always wear a dust mask
when operating this saw. ·
· Wear gloves when handling saw blades and rough materials. · Saw
blades shall be carried in a holder wherever possible.
· Select saw blades in relation to the material being cut. ·
· Use correctly sharpened saw blades and observe the maximum
speed marked on the blade. Ensure the speed marked on the saw
blade is at least equal to the speed marked on the saw ·
· Take additional care when trenching (slotting).
· The mitre saw can be safely carried by the carrying handle but only
once it has been removed from the mains power and secured in the
locked down position. Warning! Never use the guard as the lifting
and transportation purpose!
· Ensure that the arm is properly secure when bevelling.
· Keep the floor area around the machine level, well maintained and
free of loose materials.
· Ensure that you are trained in the use,adjustment and operation of
the machine.
· Do not remove any cut-offs from the cutting area until the guard is
fully locked in placed and the blade has come to rest.
· Where possible use clamps or a vice to hold the workpieces. It is
safer than using your hand.
· before each cut, make sure that the machine is stable.
· When cutting long pieces which extend well over the table width,
ensure that the ends are adequately supported at the same height as
the saw table top. Supports should be positioned in such a way to
ensure that the workpiece does not fall to the ground once the cut
has been made. A number of supports at regular intervals may be
required if the workpiece is extremely long.
· During slide cutting, always ensure that the saw blade is pushed
away from the operator.
· Always use stands to provide support for long work pieces that
overhang the turntable.
· Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
· Before making compound mitre cuts, ensure that the work head is
securely fixed in the desired position.
· Never reach over the blade to remove waste or off cuts.
8. Technical Data
Specifications:
Mains Voltage - 230V/ 50Hz
Power Consumption - 2000W
No load Speed - 4500rpm
Blade Spec - 305x30x40T
Cutting Capacity:
At 0° / 0°-
At -45° / 0° -
At 0° / -45°-
At 0° / +45°-
At -45° / -45° -
At +45° / +45° - 240x40mm
9. Operating
Avoid unintentional starting of the machine. During assembly and for
all work on the machine, the power plug must not be connected to
the mains supply.
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the accessories
provided.
Before starting the operation of the machine for the first time, check
if all parts listed in the box content section have been supplied
Note: Check the power tool for possible damage. Before further use
of the machine, check that all protective devices are fully functional.
Any lightly damaged parts must be carefully checked to ensure
flawless operation of the tool. All parts must be properly mounted
and all conditions fulfilled that ensure faultless operation.
Damaged protective devices and parts must be immediately replaced
by an authorised service centre.
5
340x104mm
240mx104m
340x55mm
340x40mm
240x55mm