djm direct DJMSL12 Manuel d'utilisation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} djm direct DJMSL12. djm direct DJMSL12 15 pages. 12 double bevel compound sliding mitre saw

Imprimer la page

· Do not slow or stop a blade with a piece of wood. Let the blade

come to rest naturally.

· If you are interrupted when operating the saw, complete the

process and switch off before looking up.

· Periodically check that all nuts, bolts and other fixings are properly

tightened.

· Do not store materials or equipment above a machine in such a

way that they could fall into it.

· Always hold the saw on parts that are insulated. If you accidentally

cut into hidden wiring or the saw's own cable, the metal parts of the

saw will become "live". Switch off at the mains and remove the plug

immediately.

· Never saw near combustible liquids or gases. · Note the direction

of rotation of the motor and the blade.

· Do not lock the movable guard in the open position and always

ensure that it is working properly, freely rotating and returning to

fully cover the teeth of the blade.

· Connect the saw to a dust collection devise and ensure that it is

operated properly. As the operator of the saw, please make sure that

you understand factors that influence exposure to dust, including the

type of material to be machined, the importance of local extraction

and the proper adjustment of hoods/baffles/ shoots of your dust

extraction system. We recommend that you always wear a dust mask

when operating this saw. ·

· Wear gloves when handling saw blades and rough materials. · Saw

blades shall be carried in a holder wherever possible.

· Select saw blades in relation to the material being cut. ·

· Use correctly sharpened saw blades and observe the maximum

speed marked on the blade. Ensure the speed marked on the saw

blade is at least equal to the speed marked on the saw ·

· Take additional care when trenching (slotting).

· The mitre saw can be safely carried by the carrying handle but only

once it has been removed from the mains power and secured in the

locked down position. Warning! Never use the guard as the lifting

and transportation purpose!

· Ensure that the arm is properly secure when bevelling.

· Keep the floor area around the machine level, well maintained and

free of loose materials.

· Ensure that you are trained in the use,adjustment and operation of

the machine.

· Do not remove any cut-offs from the cutting area until the guard is

fully locked in placed and the blade has come to rest.

· Where possible use clamps or a vice to hold the workpieces. It is

safer than using your hand.

· before each cut, make sure that the machine is stable.

· When cutting long pieces which extend well over the table width,

ensure that the ends are adequately supported at the same height as

the saw table top. Supports should be positioned in such a way to

ensure that the workpiece does not fall to the ground once the cut

has been made. A number of supports at regular intervals may be

required if the workpiece is extremely long.

· During slide cutting, always ensure that the saw blade is pushed

away from the operator.

· Always use stands to provide support for long work pieces that

overhang the turntable.

· Feed work into a blade or cutter against the direction of rotation of

the blade or cutter only.

· Before making compound mitre cuts, ensure that the work head is

securely fixed in the desired position.

· Never reach over the blade to remove waste or off cuts.

8. Technical Data

Specifications:

Mains Voltage - 230V/ 50Hz

Power Consumption - 2000W

No load Speed - 4500rpm

Blade Spec - 305x30x40T

Cutting Capacity:

At 0° / 0°-

At -45° / 0° -

At 0° / -45°-

At 0° / +45°-

At -45° / -45° -

At +45° / +45° - 240x40mm

9. Operating

Avoid unintentional starting of the machine. During assembly and for

all work on the machine, the power plug must not be connected to

the mains supply.

Carefully remove all parts included in the delivery from their

packaging.

Remove all packaging material from the machine and the accessories

provided.

Before starting the operation of the machine for the first time, check

if all parts listed in the box content section have been supplied

Note: Check the power tool for possible damage. Before further use

of the machine, check that all protective devices are fully functional.

Any lightly damaged parts must be carefully checked to ensure

flawless operation of the tool. All parts must be properly mounted

and all conditions fulfilled that ensure faultless operation.

Damaged protective devices and parts must be immediately replaced

by an authorised service centre.

340x104mm

240mx104m

340x55mm

340x40mm

240x55mm