American Standard DEEP SOAK 1640.305 Series Manuel d'installation et d'utilisation - Page 12
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} American Standard DEEP SOAK 1640.305 Series. American Standard DEEP SOAK 1640.305 Series 14 pages. Bath waste and overflow with toe tapper drain plug & deck mount bath filler
Imprimer la page
7
HAND SHOWER INSTALLATION
• Install RUBBER RING (2) on SPRAY ESCUTCHEON (1) and install SPRAY
ESCUTCHEON (1) through fifth hole on tub ledge (12" max from Spout)
making sure the SPRAY ESCUTCHEON (1) opening is directed toward tub
center. Install RUBBER WASHER (3) and LOCKNUT (4) on to SPRAY
ESCUTCHEON (1) from underside of ledge. Be sure RUBBER RING (2) is
properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3)
and LOCKNUT (4) from underside of ledge.
• Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
• Slip SHOWER HOSE (7) with HOSE CONNECTOR through SPRAY
HOLDER (5) and ESCUTCHEON (1) from above deck. Note: SPRAY
HOLDER (5) must be separate from ESCUTCHEON (1) to get SPRAY
HOSE (7) through ESCUTCHEON (1). Make sure threads on SPRAY HOLDER
(5) are facing the SPRAY ESCUTCHEON (1). Install CHECK VALVE (11) and
SEAL (8) on SPRAY HOSE (7) and connect HOSE (10) to SPRAY HOSE (7).
Install SEAL (8) on SPRAY HOSE (7) at HAND SHOWER (9) connection and
connect HAND SHOWER (9) to SPRAY HOSE (7).
NOTE: When not in use, HAND SHOWER should be seated in the HOLDER.
8
TEST INSTALLED FAUCET
• Turn VALVES (1) to "off" position.
• With handles in "off" position, turn on water supplies and check
all connections for leaks.
• Remove aerator and operate both handles and flush
the water lines throughly.
• Lift HAND SHOWER (2) from holder, direct spray into tub, rotate
DIVERTER HANDLE (3) to check HAND SHOWER (2) and HOSES for leaks.
• Turn VALVES "off".
• If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
9
Before the bathroom is completely finished, you may
want to remove spout, HAND SHOWER, and handles to
avoid damage during construction.
• To remove handles, reverse steps in STEP 4.
• To remove SPOUT (1), proceed as follows:
– Remove SET SCREW (2) using 5 mm hex wrench supplied.
– Lift SPOUT (1) off SHANK (3) carefully and remove
RUBBER RING (4).
– Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (4) is properly seated in its recess at the base of the
SPOUT (1). Make certain SET SCREW (2) is properly aligned
and tight so that SPOUT (1) is locked in place.
10
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
6
1
CAUTION: The flow rate of this Tub Filler
- 4 -
9
10
1
11
3
8
7
1
3
exceeds 20 gallons/minute at
higher water pressure.
Do not fill bathtub unattended.
2
Hex wench,
1
supplied
4
3
M965798 Rev. 1.0 (3/17)
8
5
2
4
2