DACE LUX DC12 Manuel d'installation et d'utilisation - Page 10

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} DACE LUX DC12. DACE LUX DC12 12 pages.

Imprimer la page

Step 4:

Close the Garage door/s, ensuring

that the door's rubber seal/s (1) are

si ng ﬂat on the ﬂoor.

Step 5:

Push the Drive Channel Foot (1) towards the door un l the

Door U-Brackets (2) gently touch the door (3). Slip the Door

Reinforcing Plates (4) between the Door U-Brackets and the

door. Pop rivet (5) the Door Reinforcing Plates, central to

the Door U-Brackets. Insert the pop rivet heads from the

outside.

Item (6): Drive Channel

Step 7:

With the door/s s ll closed, and ensuring that

the Door Li ing Tube and the U-Brackets are

level, pop rivet the U-Brackets to the door and

Door Reinforcing Plates.

U-Bracket A must be as close to the door guide

(1) as possible and U-Bracket B should be

placed 30mm from the end of the Door Li ing

Tube.

Side view

 30mm

SETTING AUTO CLOSE ....Menu 4

1) Ensure the ba ery is connected to the Operator.

2) Press the SET bu on to enter the Programming Menu (Pr).

3) Press the DOWN bu on un l the Auto Close Menu (AC) is visible.

4) Press the SET bu on to enter the Auto Close Menu. The display will change to the

number A0 (Auto Close Time value).

5) Press the UP and DOWN bu ons to scroll through the Auto Close me values. A0

(zero seconds or DISABLE Auto Close) to A9 (90 seconds). This is in increments of 10

seconds.

6) Press the SET bu on on the desired Auto Close me value to select.

Important: Auto Close can only be ac vated if Safety Beams have been installed. It should be noted that the

Safety Beam func on will automa cally be enabled when se ng the Auto Close func on.

SETTING THE AUXILIARY OUTPUT ....Menu 5

1) Ensure the ba ery is connected to the Operator.

2) Press the SET bu on to enter the Programming Menu (Pr).

3) Press the DOWN bu on un l the Auxiliary Output Menu (AU) is visible.

4) Press the SET bu on to enter the Auxiliary Output Menu. The display will change to

the currently selected auxiliary func on (default AL).

5) Press the UP and DOWN bu ons to scroll through the Auxiliary Output Menu

op ons.

Note: Auxiliary Output is a single connector and only one op on can be selected.

Output op ons available:

a) Auxiliary Light (AL):

This is an adjustable pulsed output, ranging from 0,25 seconds (T0) to 9 minutes

(T9), in increments of 1 minute.

This output will ac vate when the door is opened and can be used to temporarily

switch on lights or bypass alarm passives when entering the garage.

Press the SET bu on to enter the AL menu. Press the UP or DOWN bu ons to

scroll through the me op ons (T0 to T9). Press the SET bu on to select the

desired me.

b) Low Ba ery Warning (Ab):

This output will ac vate when there is a low ba ery condi on.

This output, which can be connected to a buzzer, light or external GSM, will ac vate

to indicate that the operator ba ery is low.

From the Auxiliary Output Menu (AU), press the UP or DOWN bu ons un l reaching

Ab. Press SET to select.

c) Auxiliary Trigger (At):

This output gives a pulsed trigger output every me the door is ac vated when it is in

the fully closed posi on. It can be connected to a wired remote to ac vate other

devices or to pulse stretching devices to switch lights on, bypass beams or passives

etc.

From the Auxiliary Output Menu (AU), press the UP or DOWN bu ons un l reaching

At. Press SET to select.

.................................................................................................Con nued on next page

SET

p r

A C

A 0

p r

A U

A L