DACE LUX DC12 Руководство по установке и эксплуатации - Страница 10
Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Открыватель двери гаража DACE LUX DC12. DACE LUX DC12 12 страниц.
Печатать страницуStep 4:
Close the Garage door/s, ensuring
that the door's rubber seal/s (1) are
si ng flat on the floor.
1
Step 5:
Push the Drive Channel Foot (1) towards the door un l the
Door U-Brackets (2) gently touch the door (3). Slip the Door
Reinforcing Plates (4) between the Door U-Brackets and the
door. Pop rivet (5) the Door Reinforcing Plates, central to
the Door U-Brackets. Insert the pop rivet heads from the
outside.
Item (6): Drive Channel
Step 7:
With the door/s s ll closed, and ensuring that
the Door Li ing Tube and the U-Brackets are
level, pop rivet the U-Brackets to the door and
Door Reinforcing Plates.
U-Bracket A must be as close to the door guide
(1) as possible and U-Bracket B should be
placed 30mm from the end of the Door Li ing
Tube.
Side view
6
2
1
1
30mm
B
A
10
SETTING AUTO CLOSE ....Menu 4
1) Ensure the ba ery is connected to the Operator.
2) Press the SET bu on to enter the Programming Menu (Pr).
3) Press the DOWN bu on un l the Auto Close Menu (AC) is visible.
4) Press the SET bu on to enter the Auto Close Menu. The display will change to the
number A0 (Auto Close Time value).
5) Press the UP and DOWN bu ons to scroll through the Auto Close me values. A0
(zero seconds or DISABLE Auto Close) to A9 (90 seconds). This is in increments of 10
seconds.
6) Press the SET bu on on the desired Auto Close me value to select.
3
Important: Auto Close can only be ac vated if Safety Beams have been installed. It should be noted that the
Safety Beam func on will automa cally be enabled when se ng the Auto Close func on.
SETTING THE AUXILIARY OUTPUT ....Menu 5
1) Ensure the ba ery is connected to the Operator.
2) Press the SET bu on to enter the Programming Menu (Pr).
4
3) Press the DOWN bu on un l the Auxiliary Output Menu (AU) is visible.
5
4) Press the SET bu on to enter the Auxiliary Output Menu. The display will change to
the currently selected auxiliary func on (default AL).
5) Press the UP and DOWN bu ons to scroll through the Auxiliary Output Menu
op ons.
Note: Auxiliary Output is a single connector and only one op on can be selected.
Output op ons available:
a) Auxiliary Light (AL):
This is an adjustable pulsed output, ranging from 0,25 seconds (T0) to 9 minutes
(T9), in increments of 1 minute.
This output will ac vate when the door is opened and can be used to temporarily
switch on lights or bypass alarm passives when entering the garage.
Press the SET bu on to enter the AL menu. Press the UP or DOWN bu ons to
scroll through the me op ons (T0 to T9). Press the SET bu on to select the
desired me.
b) Low Ba ery Warning (Ab):
This output will ac vate when there is a low ba ery condi on.
This output, which can be connected to a buzzer, light or external GSM, will ac vate
to indicate that the operator ba ery is low.
From the Auxiliary Output Menu (AU), press the UP or DOWN bu ons un l reaching
Ab. Press SET to select.
c) Auxiliary Trigger (At):
This output gives a pulsed trigger output every me the door is ac vated when it is in
the fully closed posi on. It can be connected to a wired remote to ac vate other
devices or to pulse stretching devices to switch lights on, bypass beams or passives
etc.
From the Auxiliary Output Menu (AU), press the UP or DOWN bu ons un l reaching
At. Press SET to select.
.................................................................................................Con nued on next page
SET
SET
SET
SET
SET
15
p r
A C
A 0
p r
A U
A L