DACE LUX DC12 Руководство по установке и эксплуатации - Страница 11

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Открыватель двери гаража DACE LUX DC12. DACE LUX DC12 12 страниц.

Печатать страницу

SETTING THE OPEN & CLOSE LIMITS ....Menu 1

1) Ensure the ba ery is connected to the operator.

2) Press the SET bu on to enter the Programming Menu (Pr).

3) Press the DOWN bu on un l Li is visible.

4) Press the SET bu on. The display will change to oL.

5) Use the UP and Down bu ons to move the door to the OPEN posi on. The Trolley

must stop 2mm away from the Sprocket Assembly. If the Trolley does not reach the

Sprocket Assembly, then a Channel End Stopper (not supplied) must be ﬁ ed

6) When the door is in the open posi on, press the SET bu on. The display will change

to cL.

7) Use the UP and Down bu ons to move the door to the CLOSE posi on.

8) When the door is in the closed posi on, press the SET bu on. The display will change

to CL. Adjust the Lower Limit Adjus ng Bolt to be 2mm above the ﬂoor.

9) The open and closed limits are now set.

SETTING THE OPENING & CLOSING FORCE ....Menu 2

1) Ensure the ba ery is connected to the operator.

2) Press the SET bu on to enter the Programming Menu (Pr).

3) Press the DOWN bu on un l the Force Limit Menu (Fo) is visible.

4) Press the SET bu on to enter the Force Limit Menu. The display will change to the

current Force Limit value F3 (this is the default se ng).

5) Press the UP and DOWN bu ons to scroll through the Force Limit values. F0

(minimum force) to F9 (maximum force). ***

6) Press the SET bu on on the chosen Force Limit value to accept.

***

Cau on: too high a force se ng could cause injury or damage!!

ENABLE OR DISABLE SAFETY BEAMS ....Menu 3

1) Ensure the ba ery is connected to the operator.

2) Press the SET bu on to enter the Programming Menu (Pr).

3) Press the DOWN bu on un l the Beams Menu (bE) is visible.

4) Press the SET bu on to enter the Beams Menu. The display will change to (by)

5) Press the UP and DOWN bu ons to toggle between ENABLE (by) and DISABLE (bn).

6) Press the SET bu on on either ENABLE (by) or DISABLE (bn) to select.

SET

SECURING THE DRIVE CHANNEL FOOT TO THE FLOOR

1) With the door/s s ll closed, and ensuring

that the Manual Release Mechanism has

been released, li the door/s by hand,

P r

holding the Cross Tube. The door/s need

only be li ed about 50cm and then lowered

again to the closed posi on. This procedure

l i

will automa cally place the Drive Channel

Foot the correct distance from the wall.

2) Without moving the Drive Channel toward

o L

or away from the door, use a Spirit Level to

conﬁrm that the channel is s ll ver cal.

3) Make marks on the ﬂoor through the two

holes in the Drive Channel Foot.

4) Move the Drive Channel slightly, enough to

allow for holes to be drilled in the ﬂoor and

c L

the 10mm wall plugs to be inserted.

(The Door Li ing Tube/s can be removed to

make this easier).

5) Move the Drive Channel back into posi on

and fasten the Drive Channel Foot to the

ﬂoor using the two coach screws

C L

Before applying power to the operator, manually li the door/s to ensure that there is free movement of the

Li ing Assembly on the Drive Channel.

Li the door/s manually to various heights and ensure that the door/s do not close under their own weight. If

they do then it will be necessary to get an experienced door ﬁ ng contractor to tension the door springs.

Place the 12 volt ba ery on top of the Drive Channel at the back of the operator and secure it in place with the

Velcro straps that are in place.

p r

Velcro straps

F o

12v Ba ery

Door U-Brackets

F 3

Drive Channel

BEFORE PROGRAMMING & COMMISSIONING THE OPERATOR

The LUX DC12 operator uses the 12V ba ery for normal opera on, it is important that the ba ery is always

Se ng the Open and Close limits:

▶

A er the operator has been assembled, fastened to the wall and a ached to the door (s), it must be

p r

programmed to recognise the door's Open and Close limits.

On ﬁrst power up, or a er a factory reset, the operator's LED display will ﬂash

door limits need to be set. The operator will not allow opera on of the door un l this process has been

b E

completed.

Note: Depending on the motor wiring polarity, the UP and DOWN bu ons on the operator may not

b y

necessarily correspond with the actual direc on that the door is moving in. The operator will automa cally

correct this once the Open and Close Limits have been set.

Follow 'Se ng the Open and Closed Limits...Menu 1' to program the limits for the door(s).

Once the limits have been set, the door can be opened and closed using the UP or DOWN bu ons on the

operator.

If, a er the ini al setup, the limits need adjus ng the Programming Menu (Pr) can be entered again by pressing

the SET bu on and the limits can be reset.

Please Note

POSITIONING & SECURING THE BATTERY

connected when the operator is in use.

. This is the indica on that the

Refer to 'Se ng the Physical End Stops' on page 13.