DoorKing MicroCLICK 8059 Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} DoorKing MicroCLICK 8059. DoorKing MicroCLICK 8059 3 pages. Rf receiver (wiegand)

Imprimer la page

MODEL 8059 MicroCLIK

The model 8059 RF Receiver is designed for use as a Stand-Alone or Wiegand applications using MicroCLIK™ transmitters. Stand-Alone installa-

tions can store up to 80 transmitter codes in its memory. It is also programmed to recognize only certain MicroCLIK™ transmitter buttons when

using multiple button transmitters.

The 8059 receiver activates a built-in dry contact form "C" relay

when a programmed MicroCLIK™ transmitter code is received.

The received code MUST match the programmed "Transmitter

Code", "Facility Code" (or not match the Facility Code if a

Wiegand controller is used), and "Transmitter Button Code"

before the receiver relay will activate.

Wiegand applications will output transmitter codes in 26-bit or 31-bit Wiegand format to an external Wiegand controller.

The MicroCLIK™ system is compatible with the HomeLink system found in many automobiles.

Installation

This receiver is NOT designed to be installed outdoors without being protected

from the weather. An outdoor enclosure is available for the receiver if required

(P/N 8057-110 - Metal Outdoor Box).

Install the 8059 receiver in a location so the antenna is NOT surrounded by

metal and is in free air as high as possible above the ground. A longer Coax

Antenna kit is available for the receiver if required (P/N 1514-073 - Includes

antenna, mounting "L" bracket and 15 feet of coax cable). An antenna amplifier

kit (P/N 8058-080) or a Yagi directional antenna kit (P/N 1514-072) is also

available for the receiver if required.

The Programming LED on the side of the case will blink as RF energy is

received. If the programming LED blinks or is on continuously, this

indicates that there may be interference on the frequency (318 MHz) and

short range may be the result. If this happens, try relocating the receiver

or remove the source of interference. An antenna amplifier or a

directional antenna may be needed. Note: Loop detectors and proximity

card readers can cause receiver interference.

Receiver Terminal Wiring

Stand-Alone Power and Device Wiring :

terminals #1 and #2. Use minimum 18 AWG wire to power the receiver.

• If DC power is used (Transformer): Terminal #1 is NEGATIVE and Terminal #2 is POSITIVE.

12-24 Volt

• Connect the receiver relay contacts to the device to be activated.

Transformer

- Receiver Terminal #3 is the relay contact Normally OPEN (N.O.)

- Receiver Terminal #4 is the relay contact Normally CLOSED (N.C.)

- Receiver Terminal #5 is the relay contact Common (C).

To Receiver Terminal #1 (Neg.)

To Receiver Terminal #2 (Pos.)

Wiegand Controller Wiring:

Receiver terminal #2 is INPUT POWER (12-24 V).

Receiver terminal #6 is Wiegand input power COMMON.

Receiver terminal #7 is Wiegand DATA 0.

Receiver terminal #8 is Wiegand DATA 1.

Use 22 AWG shielded wire, maximum

200 feet, for Wiegand controller wiring.

Connect these terminals to the

corresponding terminals on

the Wiegand controller. Refer to the

DoorKing Wiegand controller installa-

tion manual 1835, 1837 or 1838 for

specific wiring information.

DC Polarity Matters!

™

RF RECEIVER (WIEGAND)

P/N 8066-080

Be sure the antenna, coax shield

and F connector are completely

isolated from the ground.

Removable

receiver terminal

for easy wiring.

#1 - Input Power Common

#2 - Input Power

#3 - Relay Contact (Normally Open)

#4 - Relay Contact (Normally Closed)

#5 - Relay Contact (Common)

#6 - Wiegand Common

#7 - Wiegand Data 0

#8 - Wiegand Data 1

Connect 12 - 24 Volt AC or DC power to

Stand-Alone Gate Operator:

wires from the gate operator as indicated. Refer

to the chosen gate operator's installation/owner's

manual for specific wiring information.

From "Low Voltage Common"

From "Circuit Board" Power

From "Radio Open"

From "Circuit Board" Power

From "Low Voltage Common"

From "Data 0"

From "Data 1"

P/N 8067-080

MicroCLIK™ Transmitters

R e

c e i

T e r

v e r

m i

n a

(Negative)

12-24 Volt AC, 12-24 Volt DC (Positive)

To Receiver Terminal #1

To Receiver Terminal #2

To Receiver Terminal #3

To Receiver Terminal #2

To Receiver Terminal #6

To Receiver Terminal #7

To Receiver Terminal #8

Inglewood, California 90301

DoorKing Part Number

8059-080

80 Transmitter Codes

P/N 8068-080

t o r

n e c

o n

F C

L E

i n g

m m

18"

g r a

P r o

Coax

Cable

Terminals 3-4-5

rated for 30 volt,

1 amp max.

Coax

Antenna

Kit

(Included)

Connect the 3

120 Glasgow Avenue

U.S.A.