DoorKing MicroCLICK 8059 Manuel de démarrage rapide - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} DoorKing MicroCLICK 8059. DoorKing MicroCLICK 8059 3 pages. Rf receiver (wiegand)

Imprimer la page
3. 31-bit Wiegand Programming
Press and hold the Programming Button and follow the flashing LED sequence as shown below, then release the button. The programming LED
will flash once for 3 seconds indicating that the receiver is in 31-bit Wiegand output mode.
Press and
Hold Button
4. Match Facility Code Programming
Press and hold the Programming Button and follow the flashing LED sequence as shown below, then release the button. The programming LED
will flash once for 3 seconds indicating the receiver will check the facility code for a match before outputting the transmitter code.
Press and
Hold Button
One Flash
5. Ignore Facility Code Programming
Press and hold the Programming Button and follow the flashing LED sequence as shown below, then release the button. The programming LED
will flash once for 3 seconds indicating the receiver will ignore the facility code.
Press and
Hold Button
One Flash
6. Erase ALL Transmitter Codes
When memory is full, a long flash will activate when trying to program a new transmitter. To erase memory, press and hold the Programming
Button and follow the flashing LED sequence as shown below, then release the button. This will erase ALL regular and master transmitter codes.
Press and
Hold Button
One Flash
7. Master Transmitter Programming
The 8059 receiver "Master Transmitter Programming" will allow you to program up to (4) four master transmitters for easy future transmitter
additions if desired. When a "Master Transmitter" is activated, the 8059 receiver will AUTOMATICALLY go into "Learn Mode" allowing additional
transmitters to be programmed into the receiver memory without having to go through the normal "Regular Transmitter Programming" process
(See below). This is an easier way to add additional transmitters to the receiver's memory in the future. Master transmitters are NOT required to
program regular transmitters. They are NOT intended to be used as regular transmitters and should be kept in a safe place.
Press and Hold
Programming
Button
One Flash
Six
After getting into the master programming mode, select a transmitter to designate as a Master Transmitter and press
the transmitter button. This process can be done with up to 3 additional transmitters if desired, The transmitter code,
facility code and transmitter button code from the transmitter(s) are programmed into the receiver as a Master
Transmitter(s). The receiver will automatically exit the programming mode when no more transmitter codes are
received (approx. 10 seconds idle time). These 3 codes must match the master transmitter's 3 codes in order to put
the receiver automatically back into the "Learn Mode" when adding additional transmitters in the future.
8059-065-G-3-12
One Flash
Two
Approximately 6 Seconds
T
T
Two
Three
T
T
Two
Three
T
T
Two
Three
Two
T
T
Three
S
S
S
S
S
Seven
Copyright 2012 DoorKing, Inc. All rights reserved.
Release
Button
Three
One 3 Second
Flash
Approximately 10 Seconds
Four
Four
Three Times in a Row
Approximately 12 Seconds
Four
Four
Three Times in a Row
Six
Four
Four
Three Times in a Row
Four
Four
Three Times in a Row
Eight
The receiver is now in
31-bit Wiegand Output Mode
F
F
F
Four
Fi
Fi
Five
i
i
The receiver will check
Release
facility code for a match
Button
One 3 Second
Flash
Four
F
F
F
Fi
Fi
Five
i
i
The receiver will ignore
Release
Button
One 3 Second
Flash
ALL transmitters
Release
Button
will now be erased
F
F
Four
F
WARNING:
codes CANNOT be retrieved.
Four
F
F
F
You are now in Master
Release
Button
Programming Mode
Inglewood, California 90301
the facility code
Deleted transmitter
Fi
Fi
Five
i
i
120 Glasgow Avenue
U.S.A.