bolid ShPS-12 Manuel d'utilisation

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} bolid ShPS-12. bolid ShPS-12 4 pages. Fire equipment mount boxes with backup battery power supplies

Imprimer la page

ShPS-12

ShPS-12 mod.10

DESCRIPTION AND OPERATION

1.1 Purpose

1.1.1 ShPS-12, ShPS-12 mod.01, ShPS-12 mod.02, ShPS-12 mod.10, ShPS-12 mod.11, ShPS-

12 mod.12 (hereinafter referred to as ShPS-12) are meant to provide power supply for groups of installed fire

control equipment, manual call points, alarm and control panels (modules) and other fire protection equipment

requiring 12V/DC.

ShPS-12 mod.01 boxes differ from ShPS-12 boxes by a transparent window door; ShPS-12 mod.02 boxes

differ from ShPS-12 boxes by IP54 ingress protection rating.

ShPS-12 mod.11 differs from ShPS-12 mod.10 by a transparent window door; ShPS-12 mod.12 differs from

ShPS-12 mod.10 by IP54 ingress protection rating.

ShPS-12 mod.10, ShPS-12 mod.11, ShPS-12 mod.12 differ from ShPS-12, ShPS-12 mod.01, ShPS-12 mod.02

by two separate RS-485 interface lines (instead of one line, see Clause 1.2.9).

An ShPS-12 box can accommodate the following Orion ISS devices: Signal-10, Signal-20P, S2000-4,

S2000-KDL, S2000-KPB, S2000-SP1, S2000-PI, S2000-KDL-2I, Rupor mod.02, S2000-PGE, S2000-PGE

mod.01, S2000-Ethernet, S2000-RPI and other devices mountable on 35 mm top-hat DIN rail in accordance

with GOST R MEK 60715-2003.

1.1.2 ShPS-12 is designed for 24/7 continuous operation with intended output parameters, automatic

monitoring and charging of sealed backup batteries. ShPS-12 provides disconnecting backup batteries from

load circuits to avoid unacceptable discharge. ShPS-12 provides protection against open / short failures for the

battery connection circuit.

1.1.3 ShPS-12 provides visual and audible indication of the following: mains supply status (availability,

high / low voltage), backup battery status, missed batteries, disconnection of low batteries, output short

circuit / overcurrent, charger faults, output overvoltage, status of communications over the RS-485 interface

bus.

1.1.4 Being powered by mains and by batteries, ShPS-12 provides overvoltage and short-circuit protection

for 12V/DC outputs, with the output voltage being restored automatically after repairing an output short-circuit

fault.

1.1.5 ShPS-12 shall be installed in locations protected from atmospheric precipitation and mechanical

damage. ShPS-12 boxes are not designed for operating in locations where they can be exposed to explosion

and / or flammable hazards.

1.1.6 ShPS-12 is classed as recoverable and periodically serviced equipment.

1.2 Specifications

No.

1.2.1

Power Inputs

1.2.2

Primary power supply: The mains utility AC power 50/60 Hz

Backup power supply: Bolid series batteries AB 1207 (the type С or М)* or

1.2.3

similar

1.2.4

Output voltage: while powered by

1.2.5

Rated / maximum load current

1.2.6

Outputs for powering devices consuming 12 V and installed within ShPS-12

1.2.7

Maximum current per a single output 12V/dc

1.2.8

Outputs for connecting RS-485 interface lines installed within ShPS-12

For ShPS-12, ShPS-12 mod.01, ShPS-12 mod.02:

RS-485 port for connecting external devices over the RS-485 interface

1.2.9

For ShPS-12 mod.10, ShPS-12 mod.11, ShPS-12 mod.12:

Separate RS-485 ports for connecting external devices over the RS-485

interface

1.2.10

Capacity of non-volatile event log

1.2.11

Maximum power / current consumed from the mains

1.2.12

Current consumed from the batteries by the ShPS-12 itself

SHPS-12 FIRE EQUIPMENT MOUNT BOXES

WITH BACKUP BATTERY POWER SUPPLIES

ShPS-12 mod.01

ShPS-12 mod.11

Operations Manual

Parameter

ShPS-12 mod.02

ShPS-12 mod.12

Value

150...253 V

12 V, 17 Ah (2 batteries)

mains (13.6±0.6) V

batteries (13.5...9.5) V

3 A / 3.5 A **

0.65 A

95 events

120 V·A / 0.8 A

40 mA max

Table 1