Electrolux EFLS210TIW Manuel d'instructions d'installation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Electrolux EFLS210TIW. Electrolux EFLS210TIW 33 pages. Front load dryer
Également pour Electrolux EFLS210TIW : Manuel d'utilisation et d'entretien (22 pages)
Imprimer la page
- 1. Important Safety Instructions
- 2. Installation Requirements
- 3. Installation Requirements
- 4. Installation Instructions
- 4. Removing Shipping Hardware
- 4. Installing Hole Plugs
- 4. Leveling Your Washer
- 4. Connecting Inlet Water
- 4. Installation Instructions
- 5. Accessories
- 5. Instrucciones Importantes de Seguridad
- 5. Dimensiones de la Lavadora
- 5. Piezas de Repuesto
4
Installation Requirements
Electrical system requirements
CIRCUIT - Individual, properly polarized and grounded 15 amp.
branch circuit fused with 15 amp. time delay fuse or circuit
breaker.
POWER SUPPLY - 2 wire, with ground, 120 volt single phase,
60 Hz, Alternating Current.
NOTE
Because of potentially inconsistent voltage capabilities, the
use of this washer with power created by gas powered
generators, solar powered generators, wind powered
generators or any other generator other than the local utility
company is not recommended.
OUTLET RECEPTACLE - Properly grounded 3-prong receptacle
to be located so the power supply cord is accessible when
the washer is in an installed position.
Grounding type
wall receptacle
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
Power cord with
3-prong grounded plug
NOTE
GFI (Ground Fault Interrupter) receptacle is not required.
Ground requirements
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding conductor
can result in a risk of electrical shock. Check with a licensed
electrician if you are in doubt as to whether the appliance is
properly grounded.
1 The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electrical shock by a path of least resistance for
electrical current.
2 Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and
a grounding plug, the plug MUST be plugged into an
appropriate, copper wired receptacle that is properly
installed and grounded in accordance with all local codes
and ordinances or in the absence of local codes, with the
National Electrical Codes, ANSI/NFPA 70 (latest edition).
If in doubt, call a licensed electrician. DO NOT cut off or
alter the grounding prong on the power supply cord. In
situations where a two-slot receptacle is present, it is
the owner's responsibility to have a licensed electrician
replace it with a properly grounded three prong
grounding type receptacle.
Water supply requirements
Hot and cold water faucets MUST be installed within hose
length of your washer's water inlet. The faucets MUST be
3/4 inch (1.9 cm) with threading for laundry hose connection.
Water pressure MUST be between 10 and 110 psi. Pressure
difference between hot and cold cannot be more than 10 psi.
Your water department can advise you of your water pressure.
Drain system requirements
1 Drain capable of eliminating 6 gals (22.5 L) per minute.
2 A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
3 The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 56.5 in. (144 cm)
56.5"
(144cm)
max.
24"
(61cm)
min.
Clearance requirements
MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES
Alcove
0" (0 cm)
Under Counter
0" (0 cm)
0"
(0cm)
REAR
TOP
0" (0 cm)*
0" (0 cm)
0" (0 cm)*
0" (0 cm)
0"
(0cm)
0"
(0cm)
FRONT
n/a
n/a