Common Sense RC ACDC-6 Manuel d'utilisation - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Common Sense RC ACDC-6. Common Sense RC ACDC-6 8 pages. 6s balancing charger
Imprimer la page
5.3 Lithium batteries (Lilo/LiPo/LiFe) program
Press
key to enter into the parameter setting menu. You can switched
PROGRAM SELECT
at the same level menu by
flo w c h a r t o n th e le f t . W h e n y o u a r e w il li n g t o a lt e r t h e
Li** BATT
parameter value in the program, press
b lin k , t h e n c h a n g e the valu e wit h
will be stored by pressing
Mode/Esc
for more than 2 seconds to start the process.
Enter/start
"AUTO charging" this is for individual Lithium battery or some
special battery pack without balance port or cell count. The left
side of the first line shows the type of battery you select at the user
Dec.
LiPo
CHARGE
setting. The right side of the first line shows you the mode of
charge. The value on the left side of second line sets a charge
2.0A
11.1V(3S)
current and the value on the right side of second line sets the
cells count of the battery. the definition of the following screen
are all the same. (To know how to connect,plesase refer picture B)
Dec.
Inc.
"Balance charging"
balance port, the battery pack being charged should have
the individual cell connect, and connect it to the individual port
at the right side of charger with a suitable connection cable that
LiPo
BALANCE
fits with your battery pack. (see picture B)I n t h is m o d e , t h e
chargin g process will be different from ordinary charging
2.0A
11.1V(3S)
mode. the internal processor of the charger will monitor and
control the voltage of each cell of the battery pack. This can
improve the discharging perf o r m a n c e of the battery! EV
Dec.
charger use the optimised calculation to control the tolerance
Inc.
in the range of
"
Fast charging select this mode to finish charging process earlier.
Principle: When the current down to 1/5 of the current you
LiPo
FAST CHG
set during the CV term, it will stop the process and eliminate the
forcible requirement of the balance precision. (whether it is
2.0A
11.1V(3S)
been connected to the balance port), the charging capacity
may be a bit smaller than normal charging but the process time
will be reduced.
Dec.
"Storage mode " this is for charging or discharging Lithium
Inc.
battery not to be used for the time being. In order to reduce
the wastage, you can select this mode to remain the power
to 40% to store. The final voltage are different from the type
LiPo
STORAGE
of the battery, LiIo:3.75V、LiPo:3.85V、LiFe:3.3V. This is
an intellective program, If the voltage of battery at its initial
1.0A
11.1V(3S)
stage is over the volt age level to storage, the program will
start to discharge,and if it is lower, the program will start to
charge automatically. In order to ensure each battery meets
Dec.
the demand, the individual plug of the battery pack should
Inc.
be connected to the individual port of charger.
"
Discharge mode theoretically, Lithium battery do not need
to discharge, especially deep-discharge. This feature is to
LiPo
DISCHARGE
ensure the power wastage of the Lithium battery over 90%,
to avoid the overcharge of the individual battery, you should
1.0A
11.1V(3S)
Inc.
connect the balance plug of the battery to the charger, and the
current may not exceed 1C.
6
Mode
key to the screen on the left, then press
Esc
Dec. / Inc.
key. Please refer the detailed
E n te r
key to make it
S ta r t
Dec. / Inc.
key. the value
E n te r
key once. then press
S ta r t
this is for 2-6 cells of Lithium battery with
0.01V!
"
"
Picture B
E n te r
S ta r t
E n te r
key
S ta r t
connection diagram in the
Auto charging mode
5.3.1
Start to charge/discharge: after set up the mode menu correctly,
Enter
press
key for more than 2 seconds to start the process。
Start
LiPo
CHARGE
2.0A
11.1V(3S)
LiPo
BALANCE
2.0A
11.1V (3S)
LiPo FAST CHG
2.0A
11.1V (3S)
LiPo STORAGE
1.0A
11.1V (3S)
LiPo DISCHARGE
1.0A
11.1V (3S)
mode,CHG=charging at auto mode、BAL=balance charging mode 、FAS=fast charging、
STO=storage mode、DSC=discharge mode;③:elapsed time,④:charge/discharge current,
⑤:charge/discharge voltage of battery,⑥:capacity of charge/discharge
connection diagram
in the balance charging
/storage/discharge mode
This screen shows the number of cells
you set up and the processor detects."R"
shows the number of cells found by charger
and "S" is the number of cells selected by
Mode
you at the previous menu. If both number
Esc
r:3ser
s:3ser
are identical you can start charging by press
Confirm(enter)
Enter
Enter
Start >2S
button.if not, press
Start
go back to previous menu, then carefully
check the number of cells of the battery pack
Enter
to charge again. If you selected the AUTO
Start
mode or discharge mode, you can pass over
this screen directly.
Mode
Esc
This screen shows the present situation
Li3s 2.0a 12.59v
chg 022:43 00682
during charge process. to stop charging press
Enter
Start >2S
Mode
key once; As you can see in the sketch
Esc
① ②
③④
⑤
⑥
on left,①:for the cells count,②:for the operating
Individual cell
connection diagram
Mode
button to
Esc
7