Dremel GO DRAFT Manuel d'utilisation et de sécurité - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et de sécurité pour {nom_de_la_catégorie} Dremel GO DRAFT. Dremel GO DRAFT 13 pages.

Imprimer la page
This manual contains instructions for
battery charger model 510. Do not substitute
any other charger.
Before using battery charger, read all
instructions and cautionary markings on
(1) battery charger, and (2) product using
battery.
Charge only Dremel GO. Other types of
cordless tools may burst causing personal
injury and damage.
Charge tool in temperatures above +32
degrees F (0 degrees C) and below +113
degrees F (45 degrees C). Store tool in
locations where temperatures will not
exceed 120 degrees F (49 degrees C). This
is important to prevent serious damage to the
battery cells.
Do not recharge tool in damp or wet
environment. Do not expose charger to rain
or snow. Water entering battery charger may
result in electric shock or fire.
Battery leakage may occur under extreme
usage or temperature conditions. Avoid
contact with skin and eyes. The battery liquid is
caustic and could cause chemical burns to
tissues. If liquid comes in contact with skin, wash
quickly with soap and water. If the liquid contacts
your eyes, flush them with water for a minimum
of 10 minutes and seek medical attention.
Place charger on flat nonflammable
surfaces and away from flammable
materials when recharging tool. Carpeting
and other heat insulating surfaces block proper
air circulation, which may cause overheating of
the charger and tool. If smoke or melting of the
charger or tool is observed, unplug the charger
immediately and do not use the tool or charger.
Contact customer service immediately.
Make sure cord is located so that it will not
be stepped on, tripped over, or otherwise
subjected to damage or stress. Damaged
plug and cord may result in electric shock or
fire.
Disconnect the charger by pulling the plug
rather than the cord. Do not operate
charger with damaged cord or plug; have
them replaced immediately. Damaged plug
or cord may result in electric shock or fire.
Do not disassemble charger or operate the
charger if it has received a sharp blow,
been dropped or otherwise damaged in
anyway. Incorrect reassembly or damage may
Charger Safety Rules
result in electric shock or fire.
Before each use, check the battery charger,
cable and plug. If damage is detected, do
not use the battery charger. Never open the
battery charger yourself, take it to a Dremel
Factory Service Center, or qualified
serviceman only using original spare parts.
Incorrect reassembly may result in electric
shock or fire.
Do not use attachments not recommended
or sold by Dremel. Using attachments not
recommended may result in electric shock or
fire.
Unplug tool from charger when battery in
tool is fully charged. Tool left plugged in the
charger over a long period of time could lead to
tool damage and fire.
Unplug charger from outlet before storage,
attempting any maintenance or cleaning.
Such preventive safety measures reduce the
risk of electric shock or fire.
Keep the battery charger clean by blowing
compressed air on charger vents and
wiping the charger housing with a damp
cloth. Contamination may result in electric
shock or fire.
Replace battery pack if a substantial drop
in operating time per charge is observed.
Battery pack may be nearing the end of its life.
When batteries are not in tool or charger,
keep them away from metal objects. For
example, to protect terminals from shorting
DO NOT place batteries in a tool box or
pocket with nails, screws, keys, etc. Fire or
injury may result.
DO NOT PUT BATTERIES INTO FIRE OR
EXPOSE TO HIGH HEAT. They may
explode.
Battery leakage may occur under extreme
usage or temperature conditions. Avoid
contact with skin and eyes. The battery
liquid is caustic and could cause chemical
burn to tissues. If liquid comes in contact with
skin, wash quickly with soap and water. If the
liquid contacts your eyes, flush them with
water for a minimum of 10 minutes and seek
medical attention.
-5-

Battery Care

Battery Disposal

Do
not
disassemble the tool or
attempt
to