ANLIDAR MYTORQ MY9-0206L Manuel d'utilisation et d'entretien - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} ANLIDAR MYTORQ MY9-0206L. ANLIDAR MYTORQ MY9-0206L 11 pages.

Imprimer la page

1)Before changing bits from BK Series screwdriver, make sure the Forward / Reverse switch stays at

"OFF"position.

The screwdriver must be unplugged.

2) To avoid damaging the housing of screwdriver, do not allow chemicals get in touch with housing of screwdriver. Ex.: Acetone,

benzene, thinner, trichloroethylene ketone, and other similar chemicals.

3) Use screwdriver carefully, do not drop or abuse. It would be better to use with the spring balancer. If without spring balancer,

you can place the screwdriver in the suspension rack.

4) Assemble / disassemble bits : Only use fingers pull up the bit sleeve to release bits. ; Place back the bit sleeve to lock the bit

holder.

Attention : Make sure the power is off, or the Forward / Reverse switch stays at "OFF"position when assemble or disassemble

bits.

5)Connect the plug to the socket. Attention : It will cause an electric shock if the plug or the hand is wet.

6)You can adjust the torque by the torque adjuster ring. The number on the scale is not equal to the real torque, please refer to our

torque range chart, or test the torque by our torque meter.

Attention : Hi gear Do not adjust the torque setting higher than 8 on the torque scale.

Lo gear Do not adjust the torque setting higher than 4 on the torque scale.

7) a)MY9-0206L Series Trigger Start Type screwdriver : When fasten a screw, please set Forward / Reverse

Switch to "Forward".

(If the screw is reversed-thread screw, please set Forward / Reverse switch to "Reverse".) Point at the place of the bit and the

screw, press the trigger to start; When torque reaches user's setting, the clutch will shut out automatically, the power will shut

off and the motor breaks immediately, the screwdriver stop running.

b) MY9-0206P Series Push Start Type screwdriver : When fasten a screw, please set Forward / Reverse switch to "Forward".

(If the screw is reversed-thread screw, please set Forward / Reverse switch to "Reverse".) Point at the place of the bit and the

screw, push down the screwdriver to start; When torque reaches user's setting, the clutch will shut out automatically, the

power will shut off and the motor breaks immediately, the screwdriver stop running.

8) Trigger Start Type screwdriver : When loosen a fastened screw, please set Forward / Reverse switch to "Reverse".

(If the screw is reversed-thread screw, please set Forward / Reverse switch to "Forward".)

Follow the above operation, after loosening the screw, release the trigger to stop.

Push Start Type screwdriver : When loosen a fastened screw, please set Forward / Reverse switch to "Reverse"

(If the screw is reversed-thread screw, please set Forward / Reverse switch to "Forward".)

Follow the above operation, after loosening the screw, stop pushing the screwdriver to stop.

9) Operation frequency: The original setting of the frequency is 1 sec on / 3 sec off. The number of screw fastened is about 15 pcs.

Over frequently using makes the motor overheated and damage to screwdriver.

Enough heat-dissipation is good for screwdriver.

Slow speed Duty Cycle Conversion (for reference)

Based on 1000 rpm, 1 second ON/3 seconds OFF. For example, the duty cycle for 350rpm,1000-350=650，

650/1000%=65%

ON= 1*1.65= 1.65，OFF =3*1.65 =4.95 (rounded value) =2 seconds ON / 5 seconds OFF

This tool is intended for a duty cycle of 2.0 sec on, 5.0 sec off.

Slow speed (rpm)

operation frequency

900

850

800

750

700

650

10) Do not use this screwdriver to fasten wooden screws.

11) Do not operate the Forward / Reverse switch when the motor is running.

12) Whenever a screwdriver is not being used, move the Forward / Reverse switch to the "OFF" position and unplug the screwdriver.

13) Keep staying aware.

Pay attention on your work, check safety measures and every part is workable before using screwdrivers, to make sure

screwdrivers can work under original design function.

14) Use cable for the external counter and I/O box is shield cable for avoidance of electrical interference

Use Anti-interference lines.

Operations Cautions

Slow speed (rpm)

1.0 ON 3.0 OFF

operation frequency

600

1.0 ON 3.0 OFF

550

2.0 ON 5.0 OFF

500

2.0 ON 5.0 OFF

450

2.0 ON 5.0 OFF

400

2.0 ON 5.0 OFF

350

2.0 ON 5.0 OFF

Slow speed (rpm)

operation frequency

300

2.0 ON 5.0 OFF

250

2.0 ON 5.0 OFF

200

2.0 ON 5.0 OFF

150

2.0 ON 5.0 OFF

100

2.0 ON 5.0 OFF