Daspi MAGIC 1-E Manuel - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Daspi MAGIC 1-E. Daspi MAGIC 1-E 8 pages. Control panel for sliding gates

Imprimer la page

responsible for possible damages or injuries to people, objects or animals caused by any unauthorized modification of product. Do not

install this product into an explosive place

Keep scrupulously this booklet and include it into the main user manual in a suitable place well known by all the interested people.

Model

The control panel MAGIC1-E has been designed for driving 1 operator for sliding gates mod. MAX and it has an electronic clutch.

Daspi is not responsible for any different use of control panel MAGIC1-E.

List of main components

Net and motor protection's fuse T5A

Accessories protection's fuse 2A

Terminal for power supply 230 Vac 50-60 Hz

Terminal for motor and flashing light

Dip switch for control panel set up

Leeds (they turn on after power supply has been connected) will show control panel entrances connections

L1 It switches on when motor starts. When flashing, it means an

anomaly on its functions (red)

L2 Always on, it switches off by control limit-switches closing(red) L7 Always off, it switches on by control START (green)

L3 Always on, it switches off by control limit-switches opening

(red)

L4 Always on, it switches off by control of photocells (red)

RF Always off, it shows a radio interference in the area (yellow)

Check again the connections and the devices if the above led don't correspond.

Control panel programming and adjusting

The programming of DIP SWITCHES S1 must be made with control panel switched off.

IMPORTANT: Every time you set up a new feature on the DIP, wait at least 5-6 sec. before giving any control to the gate.

step by step: Open-Stop-Close-Stop

Automatic shutting time OFF

Fix working time of 2 min.

Photocells working only while closing. They stop and re-

open

Pre-flashing deactivated

Residential system deactivated. During opening it accept

any control START.

Power adjusting by trimmer TR1 (electronic clutch)

Any adjust of electronic clutch must be made from professional people in order to avoid any possible accident and reduce all crashing

risks.

•

Check that leaves on movement can be stopped at any time easily according to the actual rules.

•

Set DIP-SWITCH 1 and 6 in ON position.

•

Press START and press button S4 in order to adjust the powerful.

•

Any press increases approximately 5% the powerful of motor and it is displayed by the flashing of the led L8 (green), from 1 flash

(minimum powerful) to 8 flashes (maximum powerful). As soon as the maximum powerful is reached, another press takes the

powerful again to the minimum.

•

When power has been selected, set DIP-SWITCH 1 and 6 in OFF position (powerful is going to be automatically self-learned)

•

Power measurements on the leaves, have to be made following to actual norms.

•

Check periodically the clutch system in order to guarantee always a full safety.

Working time adjusting

DIP SWITCH 3 OFF: working time is fix, 2 minutes.

DIP SWITCH 3 ON: Self learning of working time. As soon as the programming and the installation is finished and you have tested

•

all devices' connections, put and leave DIP SWITCH 3 in ON position permanent; control panel will self learn and memorize the

working time of the motor during first operation.

Automatic shutting

•

Put DIP2 in ON

•

Press START and open completely the gate. Count the time (maximum 2 min.) and then press again START; the gate start closing

and only at its end it memorizes automatically the automatic shutting time.

•

For modifying the automatic shutting time, set DIP 2 in OFF, wait 5 seconds and remake the above process.

How to set different transmitters codes (max 32 different codes)

•

Press button "S2" for 2 seconds and then release it; Led L8 (green) flashes 5 times and then it remains on with fix light waiting for

the transmitter's code you want to memorize.

•

Press button on the transmitter you want to memorize; Led flashes for 5 times showing the transmitter has been memorized from

the receiver.

•

As soon as the maximum quantity of 32 different codes has been reached, led flashes for 10 times instead of 5 times. So before

memorizing another code, you have to delete one of the 32 already memorized.

How to erase 1 code from the receiver

•

Press button "S2" for 2 seconds and then release it; Led L8 (green) flashes 5 times and then it remains on with fix light waiting for

the transmitter's code to want to erase.

•

Press button on the transmitter you want to erase; Led L8 will flash for 5 times showing the transmitter has been erased.

10. How to erase all codes from the receiver

•

With power supply on, remove and insert fuse F2 keeping pressed button S2 for 5 seconds. Led L8 remains on for 3 seconds

showing that all codes have been erased from the memory of the receiver.

11. Terminals descriptions

OFF

Terminal for accessories – devices

M10

Terminal for antenna and accessories

Button for adjusting the pushing power (electronic clutch)

Button for transmitter's programming

Receiver incorporated

L5 Always on, it switches off by STOP (red)

L6 Always off, it switches on by control of pedestrian system

(green)

L8 Flashing every 3 sec. It shows the operation of power

adjusting and transmitters programming (green)

Open-Close-Open

Automatic shutting time ON

Self learning of working time

Photocells working also during opening: the activation of photocell

stops the gate. As soon as the obstacle is removed, the gate

continues opening

Pre-flashing activated 2.5 sec before start

During opening the control panel doesn't accept any other control

(Residential system)