ADEMCO Q16 Instructions pour l'utilisateur - Page 2
Parcourez en ligne ou téléchargez le pdf Instructions pour l'utilisateur pour {nom_de_la_catégorie} ADEMCO Q16. ADEMCO Q16 7 pages.
Imprimer la page
FUNCTION SETTING
Introduction: This system is wireless and wired alarm system. compatible 4+2 and
CONTACT ID of Ademco protocol.
It
have a function that the neighbor's alarm
system will dial for alarm instead when the phone line been cut down. The armIdisarm
function can be notice to the alarm center freely by the ClD phone display etc.
Instructions(Note: any function's settings are based on that the Alarm control
panel is in a disarmed condition. otherwise, no effective results)
1, Recorder Personal Messale
Press the recorder button one time
and
release it immediately.
Input password four numbers (Original password: 1234)
Press the recorder button again, there are two red LED flashing which is
to indicate you can start to recorder your personal message right now
within the effective distance,
20
CM away from the Alarm control panel.
The recorder time is
10
seconds.
When finished recording or recording over time, the Alarm control
panel will send out a long sound to show you are correct in this
operation.
Note: The personal message should be precise and brief:.
For example: This is xxx home, xxx district, No. xxx, The house is illegally
intruded, please assist to handle urgently.
2, Set Alarm Telephone Numbers
In total you can set 8 phone No. in this model, the first group and the second group
alarm telephone number is set for contact with the alarm center., the third group alarm
to the sixth group telephone number is set for manual telephone. If the alarm center
haven't receive the alarm info. the Alarm control panel will auto-dial the first
two alarm telephone numbers consecutively 5 times
(i.ldt'lcrrJ.
d~;;:;w
phone numbe.
-Press the set button on the A larm control pnllClI. there is a red LED
tl~'<;'~~£~~'
:L.;'
you can start to operate right now.
Input
"1
+*+(telephone nUlllber)"
Press set button to confirm the ulftrm telephone number.
2
For example: the alarm telephone number is: 8888888, the setting route is:
"set +
1
+*+8888888+set"; when finished this, the Alarm control panel will send out a
long and short sound "B" to show your operation is correct.
In the operation, " 1 * " is mean the first group alarm telephone number. And the setting
route for second group alarm telephone number is:
"set+2+*+( telephone number)+set ".Repeat the above operation to finish setting the 6
groups alarm telephone numbers. The Alarm control panel will auto-dial the alarm
telephone numbers consecutively according to this order when alarm.
If users use an extension to connect the alarm control panel and users should add one
number before dial out. For example, the one number is "9". And the alarm telephone
number is "8888888", the setting route is :
"set+ 1+*+9+*+8888888+set". If the extra number is "0", then the setting route is
""set+
1
+*+0+*+8888888+set"
3, Change the Password
-Press the set button on the Alarm control panel, there is a red LED flashing
to show you can start to operate right now.
Input "O+*+(four numbers)"
Repeat to input the "four numbers"
Press" set" button to confirm.
For example: the password is: 1234. " Set+7+*+1234+ 1234+set"
4, Set the anti-cut function On/Off
Anti-cut function On: Operation on the main panel. input "Program+2+*+0+ program"
Anti-cut function Off: Operation on the main panel, input "Program +2+*+ 1 +
program"
This function have to be active if need a neighbour instead alarm function
5, Set keypad Tone On/Off
Keypad tone on: "Program+ 3+*+
1
+Program"
Keypad tone off: "Program+3+*+O+Program
6, Protect Password Function
This function is used to protect the password when users use the Keypad of
the Alarm control panel to ArmIdisarm the Alarm control panel.
Cancel this function:
"Program+4+*+O+Program"
3