GREAT PLANES FLING Manuel d'instruction - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} GREAT PLANES FLING. GREAT PLANES FLING 16 pages. Fling arf

Imprimer la page

5. You must correctly install all R/C and other components

so that the model operates correctly on the ground and in

the air.

6. You must check the operation of the model before every

flight to insure that all equipment is operating and that the

model has remained structurally sound. Be sure to check

pushrod strings often and replace them if they show any

signs of wear or fatigue.

7. If you are not an experienced pilot or have not flown this

type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for your

first flights. If you're not a member of a club, your local

hobby shop has information about clubs in your area whose

membership includes experienced pilots.

We, as the kit manufacturer, provide you with a top

quality, thoroughly tested kit and instructions, but

ultimately the quality and flyability of your finished model

depends on how you build it; therefore, we cannot in any

way guarantee the performance of your completed

model, and no representations are expressed or implied

as to the performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

ADDITIONAL ITEMS REQUIRED

This is the list of hardware and accessories required to finish

the Fling ARF. Order numbers are provided in parentheses.

Radio Equipment

A complete radio system may be purchased for the Fling

ARF, or the individual radio components may be purchased

separately.

If purchasing a complete system, the Futaba

stick, 3-channel transmitter with R114F mini receiver and

two S3108 micro servos is recommended (FUTJ53**).

Replace the "**" with the channel number you wish to order.

(For example, if you wish to order a system on channel 44,

order FUTJ5344).

The 3FR does not come with a receiver battery pack, so the

Great Planes 4.8V 350 mAh NiMH (GPMP0950) is

recommended.

If purchasing the radio components separately, the

following are recommended items and order numbers:

• Any 2-channel (or more) 72 MHz FM transmitter

• Great Planes ElectriFly

™

(GPML0044 for low band, GPML0045 for high band)

3FR single

4-channel mini receiver w/o crystal

• Low band receiver crystal for Great Planes mini receivers

(channels 11 to 35, FUTL62**)

• High band receiver crystal for Great Planes mini receivers

(channels 36 to 60, FUTL63**)

• (2) Futaba S3108 micro servos (FUTM0042)

• Great Planes 4.8V 350 mAh NiMH receiver battery

(GPMP0950)

Note: An on/off receiver switch is not used. When ready to

fly, the battery is simply connected to the receiver.

Adhesives & Building Supplies

In addition to common household tools and hobby tools, this

is the "short list" of the most important items required to

build the Fling ARF. Great Planes Pro

are recommended.

1/4" [6mm] R/C foam rubber – (HCAQ1000)

1/2 oz. [15g] Thin Pro CA (GPMR6001)

Pro 30-minute epoxy (GPMR6047)

Plan Protector (GPMR6167) or wax paper

#1 Hobby knife (HCAR0105)

#11 Blades (5-pack, HCAR0211)

2 oz. [57g] Spray CA activator (GPMR6035)

Mixing cups (GPMR8056)

Epoxy brushes (6, GPMR8060)

Builder's Triangle Set (HCAR0480)

IMPORTANT BUILDING NOTES

When you see the term test fit in the instructions, it

•

means that you should first position the part on the

assembly without using any glue, and then slightly modify

or custom fit the part as necessary for the best fit.

•

Whenever the term glue is written, you should rely

upon your experience to decide what type of glue to use.

When a specific type of adhesive works best for that step,

the instructions will make a recommendation.

•

Photos and sketches are placed before the step they

refer to. Frequently you can study photos in following steps

to get another view of the same parts.

™

CA and Epoxy glue