GREAT PLANES FLING Руководство по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Игрушка GREAT PLANES FLING. GREAT PLANES FLING 16 страниц. Fling arf
Печатать страницу
5. You must correctly install all R/C and other components
so that the model operates correctly on the ground and in
the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
pushrod strings often and replace them if they show any
signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you're not a member of a club, your local
hobby shop has information about clubs in your area whose
membership includes experienced pilots.
We, as the kit manufacturer, provide you with a top
quality, thoroughly tested kit and instructions, but
ultimately the quality and flyability of your finished model
depends on how you build it; therefore, we cannot in any
way guarantee the performance of your completed
model, and no representations are expressed or implied
as to the performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
ADDITIONAL ITEMS REQUIRED
This is the list of hardware and accessories required to finish
the Fling ARF. Order numbers are provided in parentheses.
Radio Equipment
A complete radio system may be purchased for the Fling
ARF, or the individual radio components may be purchased
separately.
If purchasing a complete system, the Futaba
stick, 3-channel transmitter with R114F mini receiver and
two S3108 micro servos is recommended (FUTJ53**).
Replace the "**" with the channel number you wish to order.
(For example, if you wish to order a system on channel 44,
order FUTJ5344).
The 3FR does not come with a receiver battery pack, so the
Great Planes 4.8V 350 mAh NiMH (GPMP0950) is
recommended.
If purchasing the radio components separately, the
following are recommended items and order numbers:
• Any 2-channel (or more) 72 MHz FM transmitter
• Great Planes ElectriFly
™
(GPML0044 for low band, GPML0045 for high band)
®
3FR single
4-channel mini receiver w/o crystal
• Low band receiver crystal for Great Planes mini receivers
(channels 11 to 35, FUTL62**)
• High band receiver crystal for Great Planes mini receivers
(channels 36 to 60, FUTL63**)
• (2) Futaba S3108 micro servos (FUTM0042)
• Great Planes 4.8V 350 mAh NiMH receiver battery
(GPMP0950)
Note: An on/off receiver switch is not used. When ready to
fly, the battery is simply connected to the receiver.
Adhesives & Building Supplies
In addition to common household tools and hobby tools, this
is the "short list" of the most important items required to
build the Fling ARF. Great Planes Pro
are recommended.
1/4" [6mm] R/C foam rubber – (HCAQ1000)
1/2 oz. [15g] Thin Pro CA (GPMR6001)
Pro 30-minute epoxy (GPMR6047)
Plan Protector (GPMR6167) or wax paper
#1 Hobby knife (HCAR0105)
#11 Blades (5-pack, HCAR0211)
2 oz. [57g] Spray CA activator (GPMR6035)
Mixing cups (GPMR8056)
Epoxy brushes (6, GPMR8060)
Builder's Triangle Set (HCAR0480)
IMPORTANT BUILDING NOTES
When you see the term test fit in the instructions, it
•
means that you should first position the part on the
assembly without using any glue, and then slightly modify
or custom fit the part as necessary for the best fit.
•
Whenever the term glue is written, you should rely
upon your experience to decide what type of glue to use.
When a specific type of adhesive works best for that step,
the instructions will make a recommendation.
•
Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
3
™
CA and Epoxy glue