DaytonAudio WF60PA Manuel de l'utilisateur - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} DaytonAudio WF60PA. DaytonAudio WF60PA 4 pages. 60w class d full range 2.1 plate amplifier with wi-fiand bluetooth 4.0 aptx
Imprimer la page
INTRODUCTION
Congratulations on your purchase of the Dayton Audio WF60PA 60-watt plate amplifier with Wi-Fi and Bluetooth audio! The WF60PA
is a feature-packed full range Class D plate amplifier that makes it easy to add high-quality Wi-Fi and AptX Bluetooth 4.0 wireless
connectivity to your speakers. In addition to its wireless inputs, the WF60PA features RCA, 3.5mm, and optical digital inputs, plus a
subwoofer output (LFE).
The WF60PA is ideal for the project builder or OEM, with endless applications. Use the WF60PA to build multimedia speakers,
powered monitor speakers, or even retrofit existing speakers! Each Wi-Fi module is serialized for easy identification when using
multiple plate amps, and each plate amp powers its host speaker plus an additional passive unit with up to 30 watts per channel.
ASSEMBLY
Select a mounting location for the WF60PA amplifier module that allows the 30" speaker cable to easily reach the speaker or
crossover input terminals. The 30" lead is factory terminated with 0.205" disconnects for easy connection to speaker and crossover
terminals. Mount the WF60PA amplifier
module into a 4" (W) x 5-3/4" (H) cut-out
in your cabinet, and bore an 11/16"
diameter hole to mount the IR target/
BT/Wi-Fi pairing indicator PCB.
INPUTS/OUTPUTS
The WF60PA features a variety of
input connections to suit a variety
of needs:
1.) OPTICAL – Connect an S/PDIF
Toslink cable to this input. The Toslink
input supports PCM digital audio
signals via an optical cable and a
high-quality AKM digital-to-analog
converter.
2.) AUX 2 – Connect a line-level or
headphone-level signal to the 3.5 mm
AUX 2 input using a 3.5 mm to 3.5 mm
or 3.5 mm to RCA cable.
3.) AUX 1 – Connect a line-level
stereo audio signal to the AUX 1 input
using quality RCA style cables.
4.) SUB OUT – Connect a powered
subwoofer to the SUB OUT using
a standard RCA style cable. The
subwoofer plays content below 80 Hz
when connected; the speaker outputs
remain full-range.
5.) RIGHT SPEAKER OUT –
Connect a remote full-range
speaker to the SPEAKER OUT. Be
sure and pay attention to positive
and negative polarity. The amplifier
will provide up to 30 watts into a 4
ohm minimum impedance on this
connection.
6.) WPS: Wi-Fi Simple Configuration – is a network standard
to securely add devices to your wireless network.
7.) POWER – Switch to the ON position when operating the
WF60PA and the OFF position when the unit is not in use.
8.) AC INPUT – Connect line power to the AC INPUT using
the included non-polarized "figure 8" style power cord. The
WF60PA switch-mode power supply accommodates a full
range of operating voltages from 115-230V, and is double
insulated for use with non-grounded line cords.
Note: For modeling use both 2D and 3D mechanical files are available for down-
load of this plate amplifier. Files can be found on the daytonaudio.com website.
9.) SPEAKER (LEFT) OUTPUT – This speaker output is
designed to connect to the speaker inside of the enclosure, and
the Speaker (Right) output on the rear panel of the amplifier will
connect to your right passive speaker to give you a powered
stereo pair.
10.) IR CONTROL BOARD – This is the IR received that
should be installed in your speaker or project to allow control of
the amplifiers functions with the handheld IR remote control.
(2)