DaytonAudio WF60PA 사용자 설명서 - 페이지 2

{카테고리_이름} DaytonAudio WF60PA에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DaytonAudio WF60PA 4 페이지. 60w class d full range 2.1 plate amplifier with wi-fiand bluetooth 4.0 aptx

페이지 인쇄

INTRODUCTION

Congratulations on your purchase of the Dayton Audio WF60PA 60-watt plate amplifier with Wi-Fi and Bluetooth audio! The WF60PA

is a feature-packed full range Class D plate amplifier that makes it easy to add high-quality Wi-Fi and AptX Bluetooth 4.0 wireless

connectivity to your speakers. In addition to its wireless inputs, the WF60PA features RCA, 3.5mm, and optical digital inputs, plus a

subwoofer output (LFE).

The WF60PA is ideal for the project builder or OEM, with endless applications. Use the WF60PA to build multimedia speakers,

powered monitor speakers, or even retrofit existing speakers! Each Wi-Fi module is serialized for easy identification when using

multiple plate amps, and each plate amp powers its host speaker plus an additional passive unit with up to 30 watts per channel.

ASSEMBLY

Select a mounting location for the WF60PA amplifier module that allows the 30" speaker cable to easily reach the speaker or

crossover input terminals. The 30" lead is factory terminated with 0.205" disconnects for easy connection to speaker and crossover

terminals. Mount the WF60PA amplifier

module into a 4" (W) x 5-3/4" (H) cut-out

in your cabinet, and bore an 11/16"

diameter hole to mount the IR target/

BT/Wi-Fi pairing indicator PCB.

INPUTS/OUTPUTS

The WF60PA features a variety of

input connections to suit a variety

of needs:

1.) OPTICAL – Connect an S/PDIF

Toslink cable to this input. The Toslink

input supports PCM digital audio

signals via an optical cable and a

high-quality AKM digital-to-analog

converter.

2.) AUX 2 – Connect a line-level or

headphone-level signal to the 3.5 mm

AUX 2 input using a 3.5 mm to 3.5 mm

or 3.5 mm to RCA cable.

3.) AUX 1 – Connect a line-level

stereo audio signal to the AUX 1 input

using quality RCA style cables.

4.) SUB OUT – Connect a powered

subwoofer to the SUB OUT using

a standard RCA style cable. The

subwoofer plays content below 80 Hz

when connected; the speaker outputs

remain full-range.

5.) RIGHT SPEAKER OUT –

Connect a remote full-range

speaker to the SPEAKER OUT. Be

sure and pay attention to positive

and negative polarity. The amplifier

will provide up to 30 watts into a 4

ohm minimum impedance on this

connection.

6.) WPS: Wi-Fi Simple Configuration – is a network standard

to securely add devices to your wireless network.

7.) POWER – Switch to the ON position when operating the

WF60PA and the OFF position when the unit is not in use.

8.) AC INPUT – Connect line power to the AC INPUT using

the included non-polarized "figure 8" style power cord. The

WF60PA switch-mode power supply accommodates a full

range of operating voltages from 115-230V, and is double

insulated for use with non-grounded line cords.

Note: For modeling use both 2D and 3D mechanical files are available for down-

load of this plate amplifier. Files can be found on the daytonaudio.com website.

9.) SPEAKER (LEFT) OUTPUT – This speaker output is

designed to connect to the speaker inside of the enclosure, and

the Speaker (Right) output on the rear panel of the amplifier will

connect to your right passive speaker to give you a powered

stereo pair.

10.) IR CONTROL BOARD – This is the IR received that

should be installed in your speaker or project to allow control of

the amplifiers functions with the handheld IR remote control.

(2)