AFG 2.0AS Assembly and Manuel d'assemblage et d'utilisation - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel d'assemblage et d'utilisation pour {nom_de_la_catégorie} AFG 2.0AS Assembly and. AFG 2.0AS Assembly and 16 pages. Afg series
Également pour AFG 2.0AS Assembly and : Manuel d'assemblage et d'utilisation (15 pages)
Imprimer la page
iI_ ii_i
i
:
i i
i I
W
il_ _ iii_i
_i _i! I_ i i_ i i_!!_i
_
i
ii
i
/
_ii
2.0 AS rev 1.2.indd
10-11
A
B
C
D
FLAT WASHER (C)
Qty:12
(_
NYLON
NUT(E)
Qty:2
BOLT (F)
_
LOCK WASHER ( L)
25 nlm
_
Qty:2
Qty:10
BOLT (M)
BOLT (N)
_
65mm
(_
25mm
Qty:2
Qty:2
CHROME WASHER ( U)
Qty:2
SEAT HEADPAD
FLAT WASHER
SEAT BACKADJUSTMENT BAR
SEAT BACK PAD
\
SEAT BOTTOM P AD
\
NYLON
NUT
BOLT
FLAT WASHER(C) \
CENTER S UPPORT
FRAME
jjfi
BOLT(F)
BOLT(N) _
FLAT
_-.
SEAT BACK
WASHER (C)
_
ADJUSTMENT
PiN
jjJJ
• r_ j S
SEAT BOTTOM /. .................
"-_
ROLLER
ADJUSTMENT
BAR
BOLT (M)
;HROME W ASHER (U)
LOCK WASHER (L)
LEG ROLLER
OpenHARDWARE BAG 4.
SUPPORT T UBE
_
BOLT (F)
WATER
BOTTLE
HOLDER
Attach SEAT HEAD PADto CENTER
SUPPORT FRAME using 4 BOLTS (F) and 4 FLATWASHERS (C),as shownin diagram.
Install SEAT BACK ADJUSTMEHT
PIN in CENTER SUPPORT F RAME. ( Fullythreadinto
CENTERSUPPORTFRAMEafter SEATBACKAD]USTMEHT BAR is installed.)
Attach SEAT BACK PADto SEAT BACK AD]USTMEHT BARusing 4 BOLTS (F) and 4 FLAT
WASHERS (C),and insert into CENTER SUPPORT F RAME as shownin diagram.
E
Attach SEATBOTTOM PAD to SEATBOTTOM ADIUSTMEHT BAR using 2 BOLTS(M) and 4
FLATWASHERS (C) and 2 NYLONNUTS(E), and insert into SEATWELDMENT a s shown in
diagram.
F InstallFOAM ROLLERS o ntoLEGROLLER SUPPORT T UBE using 2 BOLTS (F), 2 LOCK
WASHERS (L) and 2 CHROME WASHERS (U),as shownin diagram.
G Attach W ATERBOTTLE HOLDERtoCENTERSUPPORTFRAME using 2 BOLTS(H).
tt Tightenall hardwarein Step4.
A
B
C
D
E
F
G
H
FLAT WASHER ( C)
Qty:8
_
YLON
NUT(E)
Qty:4
(_
FLAT WASHER (I) _
NYLON
Qty:4
NUT(K)
Qty:2
BOLT (0)
lOOmm
Qty:2
BOLT (P)
_._)
70mm
_-
Qty:2
RUBBER
BUMPER
Qty:2
BOLT (Q)
40 mm
Qty:2
Open HARDWARE BAG 5.
Attach L OWER MOUNTING B RACKET ( after
removing pre-instafled
guide rod bolts) to BASE
FRAME in desiredlocation, using 2 BOLTS(P),
4 FLATWASHERS(C)and 2 NYLONNUTS(E).
NOTE: Referto page 25 for mountingpositions.
Position each GUIDERODso that the mounting
holes are in the upper position, and insert
GUIDERODSinto corresponding sleeves in
LOWERMOUNTING BRACKET.
Slide I UPGRADE SPACER and thenslide ]
RUBBER BUMPER onto eachguiderod, as
shown in diagram.
Install each WEIGHTPLATEonto guide rod as
shown in diagrarn. Ensure than the weight pin
selector slot is positioned downward and in
same direction.
Install BAYONET onto GUIDERODSas shown in
diagram.
Re-install GUIDEROD bolts into LOWER
MOUNTINGBRACKET.
Instafl UPPER MOUHTIHG B RACKET t o top of
GUIDE RODS, a s shownin diagram, using 2
BOLTS (Q),4 FLATWASHERS (I) and 2 NYLON
HUTS ( g).
UPPERMOUNTING BRACKET
\
FLAT WASHER(i) \
NYLON NUT(K)
BOLT(0)
j/
UPPER
PULLEY
ASSEMBLY
BOLT (Q)
/
\ FLAT
WASHER (I)
_-BAYONET
WEIGHT
/ PLATES
BASEFRAME
UPGRADE
SPACER
!
\
LOWER MOUNTING
BRACKET
FLAT WASHER (C)
NYLON NUT(E)
Attach U PPERMOUHTIHGBRACKETto UPPERPULLEYASSEMBLY using 2 BOLTS(0), 4
FLATWASHERS(C),and 2 NYLONNUTS(E).
NOTE.. Ensurethat the UPPER MOUHTIHG B RACKET's positioncorresponds to the position
of the LOWER MOUNTING B RACKET beforesecuringit to the UPPER PULLEY ASSEMBLK
]
Tightenall hardware.
/
iii _
i i
ii _ _ii ii
12/28/07
10:16:08
AM